
 |
ENGINEERED
STEEL PRODUCTS |
Priced
Full Line Products Catalog |
20
Technology Way West Greenwich, RI 02817
Toll free:(800) 421-0314 In RI:(401) 272-4570 Fax:(401)
421-5679 |
 |
|
 |
Back to Product Category
NO.
633 OUTDOOR RECYCLED RUBBER
STAIR TREAD
|
|
|
|
|
|
|
|
 |
|
Our
new No. 633 Outdoor Rubber Stair Tread is an excellent stair tread
for exterior applications. This tread, made from 100% recycled tires, is
available in black color only in a diamond pattern with a 3 smooth
back
border in square nose pattern only. |
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
SPECIFICATIONS: |
|
|
|
|
|
|
|
|
|
Furnish
and install No. 633 Outdoor Recycled Rubber
Stair Treads; 1/4 thick 12 deep; 1-1/2 square nose;
made from 100% recycled tires. Select from standard
lengths of 36, 42, 48, 54, 60 or 72.
Black color only.
|
|
|
|
|
|
|
|
 |
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click the Model No. of the item you wish
to purchase. |
|
|
|
|
PRICING
FOR RUBBER TREAD NO. 633 |
|
Model No. |
Standard Length |
Approx. Weight Per
Tread |
Price Per Tread (ea.) |
633-36 |
36" |
4.0 lbs. |
$117.24 |
633-42 |
42" |
4.7 lbs. |
$136.74 |
633-48 |
48" |
5.3 lbs. |
$156.30 |
633-54 |
54" |
6.0 lbs. |
$175.80 |
633-60 |
60" |
6.7 lbs. |
$195.36 |
633-72 |
72" |
8.0 lbs. |
$234.42 |
|
|
|
ADHESIVES |
|
#775
Epoxy Adhesive - Environmentally Friendly
The only recommended adhesive for use with Disc-O-Tile. May be used with
other rubber stair treads, tile and flooring.
Because of flame spread properties, other adhesives will not bond Disc-O-Tile
to the floor. A two-part solvent-free
adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers
approximately 150 square feet per unit. |
|
Model No. |
Size |
Std. Ctn |
Approx. Wt. (ea) |
Price (Unit) |
775 |
1 unit |
1 |
12 lbs. |
$161.90 |
|
|
How
To Install Outdoor Rubber Stair Treads |
|
The
purchase of rubber stair treads warrants proper installation and maintenance
procedures in order to assure
complete satisfaction. For unusual and special conditions, contact the factory
for recommendations. |
Where
To Install |
|
Install
stair treads on any smooth dry step provided the shape of the step conforms
to the underneath contour of the
stair tread; particularly at the section where the flat part of the tread
joins the nosing. A tight fit between stair treads
and steps is essential. We recommend the use of Epoxy Nose Caulk on
all stair tread installations. |
Where
Not To Install |
|
If
the shape of the steps does not conform to the shape of the stair treads
and cannot be altered to conform, we do not
recommend installation of treads unless special instructions are carefully
followed. |
Room
Temperature |
|
Materials,
installation area, and adhesives should be no less than 70 degrees Fahrenheit
(21 degrees C) 48 hours prior
to, during and after installation. |
Repairing
Worn and Uneven Edges |
|
Repair
worn, uneven, or misaligned edge of steps. |
|
If
an open space exists underneath the nosing of the thread when it is applied
against the step you must fill
the space with Epoxy Nose Caulk. It is essential that there be no space
between the step and the stair tread
when the installation is completed. |
|
Preparation
for Installation |
|
Surfaces
of steps must be level, clean, dry and free from oil, grease, rust, paint,
varnish and old coverings,
adhesives and any other foreign substance. Wooden steps should be thoroughly
nailed down. |
|
Worn
or dished-out steps, cracks, holes, depressions or any other irregularities
on the step should be
repaired by filling or sealing and smoothing with an underlayment compound. |
Fitting
and Cutting |
|
Treads
are usually supplied over size, with untrimmed ends, to allow extra material
to compensate for variations
in step dimensions. |
|
Treads
should be individually trimmed to fit each step, both in depth and from
side to side. The rear edge should
be cut with a slight underbevel for a better fit. The stair treads can be
marked with an awl and cut using a steel straight
edge and a linoleum knife. |
|
The
most important factor in proper stair tread installation is to see that
no air space exists underneath the nosing part
of the treads. The tread must not flex or move as traffic walks across the
steps. Epoxy Nose Caulk should be used as
described on the label. |
|
It
is important to use the correct adhesive. The recommended adhesive for the
outdoor rubber stair treads is
No. 775 Epoxy Adhesive. |
Installation
of Rubber Stair Treads |
|
After
the steps have been prepared and the stair treads cut and fitted as described,
begin installation by
spreading adhesive on the stair completely covering the surface and the
nosing. |
|
Always
follow instructions on label of adhesive container. |
Install
Stair Treads |
|
Set
the stair tread into its proper position on the step, beginning at the nosing
and pushing back firmly and as tightly
as possible, holding up the back surface of the tread. After nosing is completely
in place, begin at the front and move
back on the surface of the tread towards the riser; the tread should be
pushed down firmly onto the step. |
|
After
installation is completed, roll newly installed stair treads with a hand
roller, making certain that the stair tread
nosing is fitted tightly against the step nosing. If any difficulty is experienced
in holding the nosing to an understair, use
a few hardened steel headless brads to secure it while the adhesive is drying. |
Final
Precautions |
|
Any
adhesive or caulking compound on the surface of the stair treads should
be wiped off before it dries, using a
cloth dampened in denatured alcohol. If adhesive has dried, remove carefully
with #00 steel wool and denatured
alcohol. Rub lightly to avoid dulling and scratching stair treads. |
|
It
is important that traffic be kept off the newly installed stair treads,
until the adhesive has set up sufficiently
to prevent movement and assure a firm bond. |
|
Where
construction work by other trades requires traffic over newly installed
stair treads, protect treads with
heavy building paper or planking as needed. |
|
Do
not wash or apply any surface treatments for about one week after installation
to allow sufficient time for
the stair treads to become tightly bonded to the steps. |
|
Maintenance
Tips |
|
The following
simple steps for correct care are recommended:
Daily sweeping with soft hair push broom, also before and between washings,
will cut down the number of
washings and remove dirt and foreign matter.
During bad weather any accumulated rain or slush should be wiped promptly
from stairs to prevent slipping.
Wipe up spillage before it has a chance to harden.
When cleaning is necessary, wipe with cloth or damp mop, using clean room-temperature
water. Do not
flood stairs.
In stubborn cases, damp mop with room temperature water and solution of
liquid detergent suitable for
rubber floor covering or a solution of ammonia and water. Immediately
rinse stairs with clean room temperature
water, changing rinsing water frequently. |
|
|
Outdoor Recycled Rubber Stair
Tread, Outdoor Rubber Stair Tread, Rubber Stair Treads, Stair Treads,
Square Nose
Rubber Tread, Exterior Rubber Stair Treads, Recycled Treads, Diamond Design
Rubber Treads, and Black Stair Treads
from your source for material handling equipment. |
Back
to Product Category |
 |
|