Belt Conveyors, Wire Mesh Belt Conveyor, Wire Belt, Conveyors

ENGINEERED STEEL PRODUCTS

Priced Full Line Products Catalog

20 Technology Way • West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401) 421-5679

Back to Product Category

MODEL TW
HORIZONTAL WIRE MESH BELT CONVEYOR


		The Model TW with wire belt can carry hot or cold parts from ovens or freezers. Can be used in drying operations.

		3 Belt Widths

		Wire Mesh Belt

		Adjustable MS-Type Floor Supports Available

LOAD CAPACITY CHART @ 65 FPM

HP	BED WIDTHS - 16" to 28"
	TOTAL LOAD (Lbs.)
	UP TO 50'	UP TO 100'
1/2	850	350
1	1950	1500


STANDARD SPECIFICATIONS

BELT–1/2 in. x 1 in. flat galvanized wire mesh belt. Maximum product temperature 350°F.	RETURN IDLER–Adjustable 1.9 in. dia. pre- lubricated ball bearings.

BED–Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 6 in. Mounted in 6-5/8 in. x 12 ga. powder painted formed steel channel frame bolted together with splice plates.	TAKE-UP–Take-ups at tail pulley. Provides 4 in. of belt take-up.

	BEARINGS–Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts. Pre-lubricated ball bearings in tread rollers.

CROSS BRACING–Rods with turnbuckles are fastened to underside of bed to provide alignment of bed rollers to insure correct belt tracking. Required on every other section 30 ft. bed lengths and over.

	SPEED REDUCTION–Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket.

	MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face.

END DRIVE–Located on discharge end of conveyor, chain guard on left hand side.

	CAPACITY–Maximum load per linear foot of conveyor 75 lbs. NOT TO EXCEED capacity in chart.

DRIVE SPROCKETS–6 in. pitch dia. multiple cast iron sprockets with 1-3/16 in. dia. shaft 6 in. centers.

TAIL PULLEY–4 in. dia. with 1 in. dia. shaft at bearings. Sprocket at each end.
		FLOOR SUPPORTS–Now supplied as optional equipment.
		FLOOR SUPPORTS–Now supplied as optional equipment.
SNUB IDLER–Adjustable 2-1/8 in. dia. pre- lubricated ball bearings.
	BELT SPEED - Constant 65 FPM.



OPTIONAL EQUIPMENT

FLOOR SUPPORTS–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support.		V-BELT DRIVE–V-Belt supplied between motor and reducer.

		O-RING DRIVE CHAIN–With sealed in lubricant (Recommended for applications that do not permit regular lubrication).

		CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.

BED–Slider bar in place of roller bed.

BELT–Other widths than standard, galvanized low carbon steel, bright high carbon steel or stainless steel. 1 in. or 1/2 in. x 1/2 in. mesh available. Maximum product temperature 750°F with high carbon steel belt.

		MOTORS–Energy efficient, single phase, other characteristics. 1 HP maximum.

		ELECTRICAL CONTROLS–Non-reversing magnetic starters and push-button stations. AC variable frequency drive.

BELT SPEED–Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM and with variable speeds. NOTE: Capacity affected with speed change.


PRICES FOR COMPLETE CONVEYOR INCLUDE:

1/2" x 1" Wire Mesh Galvanized Belt		Totally Enclosed Chain Guard

1.9" Dia. Roller (Rollers on 6" Centers) in a 6-5/8" x 12 Ga. Steel Channel Frame		65 FPM Belt Speed

		Less Electrical Controls
		Less Electrical Controls
6" Pitch Dia. Drive Sprockets
6" Pitch Dia. Drive Sprockets		Less Supports
		Less Supports
"C" Face Speed Reducer - Sealed Worm Gear

1/2 HP - "C" Face Totally Enclosed Motor (Specify Exact Voltage)


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

IMPORTANT NOTES...

OTHER LENGTHS

OTHER WIDTHS

Other lengths not listed in price chart are available. For
"IN-BETWEEN SIZES", use next larger. Overall
Length "A" price. For lengths longer or shorter than
those shown in chart, please contact us.

For "IN-BETWEEN WIDTHS", use next width plus
10%. For widths up to 52" OAW, interpolate plus
10%. For widths over 52" OAW, contact us.

NON-STANDARD WIDTHS

FLOOR SUPPORTS

Floor Supports are not included in base price. There
are two (2) stationary floor supports required for
the first bed section and one (1) support per bed
section thereafter.

INTERMEDIATE BEDS

Use per foot price of width x required length,
supports not included.

SIZE TO ORDER Overall Length "A"	Bed Length "L"	Wire Mesh Belt Width
		6"	8"	12"	18"	20"	24"
		Roller Bed Width
		10"	12"	16"	22"	24"	28"
6'-1"	5'	$4,659	$4,814	$5,124	$5,588	$5,743	$6,052
11'-1"	10'	$5,134	$5,332	$5,728	$6,321	$6,520	$6,915
16'-1"	15'	$5,609	$5,851	$6,333	$7,055	$7,297	$7,778
21'-1"	20'	$6,084	$6,369	$6,936	$7,789	$8,074	$8,641
26'-1"	25'	$6,559	$6,888	$7,541	$8,523	$8,851	$9,504
31'-1"	30'	$7,034	$7,406	$8,145	$9,256	$9,628	$10,367
36'-1"	35'	$7,509	$7,924	$8,750	$9,990	$10,405	$11,230
41'-1"	40'	$7,984	$8,443	$9,354	$10,724	$11,182	$12,093
46'-1"	45'	$8,459	$8,961	$9,959	$11,457	$11,959	$12,956
51'-1"	50'	$8,934	$9,479	$10,563	$12,191	$12,736	$13,820
56'-1"	55'	$9,409	$9,998	$11,168	$12,925	$13,513	$14,682
61'-1"	60'	$9,885	$10,516	$11,772	$13,659	$14,290	$15,546
66'-1"	65'	$10,360	$11,035	$12,377	$14,392	$15,067	$16,408
71'-1"	70'	$10,835	$11,553	$12,980	$15,126	$15,844	$17,272
76'-1"	75'	$11,310	$12,071	$13,585	$15,860	$16,621	$18,134
81'-1"	80'	$11,785	$12,590	$14,189	$16,593	$17,398	$18,998
86'-1"	85'	$12,260	$13,108	$14,794	$17,327	$18,175	$19,860
91'-1"	90'	$12,735	$13,626	$15,398	$18,061	$18,952	$20,724
96'-1"	95'	$13,210	$14,145	$16,003	$18,795	$19,729	$21,586
101'-1"	100'	$13,685	$14,663	$16,607	$19,528	$20,506	$22,450
Per Foot Price		$95.50	$104.30	$121.00	$146.50	$147.60	$173.20

PRICES FOR OPTIONAL EQUIPMENT

OPTIONAL DRIVES

FLOOR SUPPORTS

Drive	BED WIDTHS
Type	16" to 22"	28"
End Drive (V-Belt)	$246.50	$246.50
Side Mounted	$371.30	$482.20
Overhead	$552.60	$704.30

Not included in base price. Use chart below for
required elevation.

'MS" SUPPORT

Model No.	Adjustment to Top of Belt	Price Each
MSL-1*	9-3/8" to 10-3/8"	$58.40
MSL-2*	10-3/8" to 12-1/8"	$58.40
MSL-3*	12-1/8" to 14-3/4"	$58.40
MS-1*	14-3/8" to 16-1/8"	$58.40
MS-1.2*	15-3/8" to 17-1/8"	$58.40
MS-1.4*	16-3/8" to 18-1/8"	$58.40
MS-2	17-3/8" to 20-3/8"	$60.40
MS-3	20" to 23"	$66.40
MS-4	23" to 29"	$76.40
MS-5	27" to 33"	$79.80
MS-6	31" to 43"	$88.10
MS-7	41" to 53"	$130.20
MS-8	53" to 65"	$148.50
MS-9	65" to 77"	$162.80
MS-10	77" to 89"	$185.60
MS-11	87" to 99"	$205.20
MS-12	99" to 111"	$214.60

#50 O-Ring Drive Chain ............Add ...........

$284.40

CONSTANT AND VARIABLE SPEEDS

Constant C-Face - Within 15-70 FPM ......No Charge

Constant V-Belt - Minimum of 4 FPM ....................

................................... Use V-Belt Drive Add-On

DRIP PANS

Add-On per foot of conveyor .....................

$55.60

UNDERSIDE BED COVERS

Add-On per foot of conveyor .....................

$29.60

GUARD RAILS

Adjustable Universal Channel Guard Rail

Both Sides ...................per foot .................

$15.10

One Side .....................per foot .................

$7.80

NOTE: PC Type guard rail only. Available in 5’ and 10’
lengths from factory. Contact us for other lengths.

NOTE: MS-7 to MS-12: Knee Braces included in price.

HEIGHT (Both Sides-Per Foot)	TYPE
HEIGHT (Both Sides-Per Foot)	Solid Side	PC Type
2"	$31.40	N/A
3-1/2"	N/A	$32.40
4"	$32.30	N/A
6"	$34.60	$34.60
9"	$40.30	$40.30
12"	$44.80	$44.80

Knee Braces ..............Add per pair ............

$30.00

*Less than 9-1/8" top of roller elevation-

Side Mounted Drive Required.

ELECTRICAL CONTROLS

(See Below)

GALVANIZING

NOTE: Solid Side Guards mount vertically on
outside of conveyor bed, PC Type Guards mount
on top of bed.

DRIVE COMPONENT DEDUCTS

OPTIONAL ROLLER CENTERS

Less Motor Drive, Motor Mount and Guards, but
with Shaft Extension and Sprocket.....................

3" Centers
10"-12" ..........per foot of conveyor............
16"..................per foot of conveyor............
22"..................per foot of conveyor............
28"..................per foot of conveyor............

$23.40
$23.40
$28.40
$32.70

..............................Deduct ......................

$694.20

Less Motor Only (1/2 HP-208/230/460/
575V- 3 Ph.-60Hz.).........Deduct ..............

$258.30

*Less Reducer ................Deduct ...............

$318.70

SLIDER BAR

*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied.

Slider Bar Construction (Herringbone Type Design)
in place of rollers ..................................................

...................Per Foot of Conveyor .............

$32.40

MOTORS

Extra Motor Price for OTHER THAN: 1/2 HP–208/230/460/575 V–3 Ph.–60 Hz.–Totally Enclosed. Speed affects
horsepower requirements.

H.P. REQ.	TOTALLY ENCLOSED		PREMIUM ENERGY EFFICIENT		BRAKE MOTORS
H.P. REQ.	200/208/230/ 460/575V 3 Ph.-60 Hz.	115/230V 1 Ph.-60 Hz.	230/460V 3 Ph.-60 Hz.	575V 3 Ph.-60 Hz.	Holding Brake 208/230/ 460/575V 3 Ph.-60Hz.	Holding Brake 115/230V 1 Ph.-60Hz.
1/2	N/C	$39.30	$400.90	$400.90	N/A	N/A
1	N/A	$143.20	$498.10	$498.10	$1,051.40	$1,219.30
2	N/A	$1,206.80	$972.10	$972.10	$1,639.70	$3,154.60

* Note: "High Cycle Brakemotors" are used for indexing and are rated for 30 cycles per minute. Add-On Prices
Include 5AC Reducer, Heavy Duty Motor Base Plate, and #60 Chain and Sprockets with Taper Bushed Hubs.

** Note: "High Cycle Brakemotor" Add-On Prices Include 5AC Reducer, Heavy Duty Motor Base Plate and
Timing Belt Drive.

Note: SSB and D Series are Holding Brakes and are NOT rated for cycling.


				Order Online, by Phone, or by E-Mail
				~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

CEILING HANGERS
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated fully threaded rods ......................................................................
		$147.90
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized fully threaded rods .......................................................................
		$176.60
	Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully threaded rods................................................................................
		$218.40
	Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods.................................................................................
		$359.60
	Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.................................................................................

		$362.60
	Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods..................................................................................
		$419.40
	Ceiling Hanger Brackets, Less Rods Only ....................................	$93.10
	Extra Length Rods:
	(2) 8’-0” long x 5/8” dia. unplated fully threaded rods ..................	$54.20
	(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ...............	$83.40
	(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................	$125.20
	(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods .............	$266.30
	(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................	$269.60
	(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods .............	$326.50
	Hex Coupling Nuts for Rods .........................................................	$4.90
	Above noted delivery times determined by delivery time of model ordered.

POLY-TIER SUPPORTS

PRICES FOR COMPLETE
SUPPORT INCLUDE:

IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.

• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
conveyor)
• "U" Brackets
• Single Width Conveyor Only

CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs

(2) TIER POLY-TIER SUPPORTS
36"	$311.36
42"	$320.01
48"	$328.56
54"	$337.00
60"	$345.65
66"	$354.42
72"	$362.86
78"	$371.52
84"	$380.00
90"	$388.50
96"	$397.27
102"	$405.93
108"	$414.60
114"	$423.69
120"	$431.46

(3) TIER POLY-TIER SUPPORTS
36"	$439.01
42"	$447.80
48"	$456.30
54"	$464.80
60"	$473.42
66"	$482.18
72"	$490.62
78"	$499.30
84"	$507.80
90"	$516.40
96"	$524.90
102"	$533.60
108"	$542.46
114"	$550.45
120"	$559.00


				Order Online, by Phone, or by E-Mail
				~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

ELECTRICAL CONTROLS AND DRIVE SECTION

MANUAL START SWITCH or
SAFETY DISCONNECT

LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER

#032.1014.........................................

$213.01

#033.2032 & #033.2072..................$555.67
Nema 4

"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)

LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER

#033.2033& #033.2072...................$332.11
Nema 4

REVERSING DRUM SWITCH

#032.103..........................................

$854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase

PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range

FOOT SWITCH WITH GUARD

#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range

#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.

PHOTO EYE, ON-OFF TYPE

#EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC

POWER CORD AND PLUG (20')

POWER CORD WITH PLUG ONLY 20' LONG
Model No.	Voltage	HP Rating	Prices
EA-039-1A	115/1	1/2-3/4	$106.67
EA-039-2A	115/1	1	$106.67
EA-039-3A	115/1	1 1/2	$155.18
EA-039-4A	230/1	1/2-1	$106.67
EA-039-5A	230/1	1 1/2-2	$109.67
EA-039-6A	208-230/3	1/2-2	$178.60
EA-039-7A	460/3	1/2-2	$178.60

POWER CORD WITH PLUG 20' LONG WITH MANUA
Model No.	Voltage	HP Rating	Prices
EA-039-1B	115/1	1/2-3/4	$173.16
EA-039-2B	115/1	1	$330.67
EA-039-3B	115/1	1 1/2	$377.96
EA-039-4B	230/1	1/2-1	$293.04
EA-039-5B	230/1	1 1/2-2	$330.67
EA-039-6B	208-230/3	1/2-2	$362.97
EA-039-7B	460/3	1/2-2	$362.97

MOUNTING BRACKETS FOR PHOTO
EYE #033.2122

B-05165...........................................$118.10

AIR PRESSURE SWITCH

#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH

#032.285 with 032.2851 Turnbuckle
...........................................................$696.08
Nema 4

"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE

#032.281...one side.................$7.44 per / ft.
both sides..............$15.87per / ft.

EMERGENCY PUSH BUTTON

#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE

#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48

NOTE: PRICING LISTED NOT MOUNTED
OR WIRED

"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC

#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

CONTROLLER PRICES

AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size	115 Volt		208/230 Volt
1/2	VSC-12-10		VSC-12-12
Price	$1,491.84		$1,189.37
1	VSC-12-11		VSC-12-13
Price	$1,724.27		$1,391.05
2	N/A		VSC-12-14
Price	~		$1,794.20
THREE PHASE CONTROLLER INPUT
Motor Size	208/230 Volt	460 Volt	575 Volt
1/2	VSC-01-15	VSC-01-18	VSC-12-29
Price	$1,564.99	$1,656.34	$2,155.73
1	VSC-01-16	VSC-01-19	VSC-12-29
Price	$1,579.75	$1,794.20	$2,155.73
2	VSC-01-17	VSC01--20	VSC-12-30
Price	$1,978.69	$2,070.37	$2,663.45

REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS

HP	Part No.	Price
1/2	032.351 230/460	$618.71
1	032.353 230/460	$705.52
2	032.355 230/460	$797.31
1/2	032.3512 575	$1,449.11
1	032.3532 575	$1,611.17
2	032.3552 575	$1,897.10

IMPORTANT NOTES...

• All above motors are 230 / 460 / 575 Volt, 3 Phase.
• All above V/S Drive Kits include NEMA 1 / IP30
Junction Box, Controller and Motor.
• Good for cycle rates of up to 15 cycles per minute, at
1/2 second ramp time, with a maximum speed of 250
FPM.
• Drawing No. DG-001146.

OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)

$675.20

• When AC Variable Speed Controller is used with a
Brake Motor, A Brake Relay Kit (EA-068A) is
required. Add an additional $542.68 for this option.)

Brake Relay Kit (EA-068A)..............................

$542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE

Part No.	Description	Price
EA-VSC-01-CB	2 HP Electronic Clutch-Brake Kit	$5,058.00

OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)

$675.20

KIT INCLUDES

Part No.	Description
VSC-01-20	AC Variable Speed Controller, 460 Volt, 3 Phase
032.345	2 HP 460 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

IMPORTANT NOTES

• Good for cycle rates of up to 60 cycles per minute.
• 1/10 second Accel and Decel time, with 350 FPM
Maximum Speed.
• 230 or 460 Volt Only, Other Voltages, Contact us.
• Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
• Price Includes 5AC Reducer and #60 Chain and
Sprockets

Part No.	Description
VSC-01-17	AC Variable Speed Controller, 230 Volt, 3 Phase
032.345	2 HP 230 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)

An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.

THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	MOTOR DUTY	NON-REVERSING					REVERSING
H.P.	MOTOR DUTY	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE
1/2	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B25	EN-46B16	EN-57B10	$1516.60	ER-20B40	ER-23B25	ER-46B16	ER-57B10	$2,023.30
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B16	EN-46B10				ER-23B16	ER-46B10
1	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B40	EN-46B25	EN-57B16		ER-20B40	ER-23B40	ER-46B25	ER-57B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
1-1/2	GEARMOTORS	EN-20C10	EN-23B63	EN-46B40	EN-57B25		ER-20C10	ER-23B63	ER-46B40	ER-57B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
2	STANDARD EASY CLEAN ENERG. EFF.	EN-20C10	EN-23C10	EN-46B40	EN-57B40		ER-20C10	ER-23C10	ER-46B40	ER-57B40
			EN-23C10	EN-46B40				ER-23C10	ER-46B40
			EN-23B63	EN-46B40				ER-23B63	ER-46B40

SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	NON-REVERSING		REVERSING		NON-REVERSING		REVERSING
	115 VOLT	PRICE	115 VOLT	PRICE	230 VOLT	PRICE	230 VOLT	PRICE
1/2	EN-1SC10	$1,182.40	ER-1SC10	$2,023.30	EN-2SB63	$1,435.60	ER-2SB63	$2,023.30
1	EN-1SC16		ER-1SC16		EN-2SC10		ER-2SC10
1-1/2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10
2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10


• Manual Start-Stop Switch Kit			• Start-Stop Push Button Kit, Remote Mounted
	EA-000001 ......................................	$242.09		EA-000002.......................................	$242.09
	Includes: 032.1014 Manual Start Switch, Nema 1, B-21467 Mounting Bracket with Mounting Hardware			Includes: 033.1955 Push Button Station, One Direction, Nema1, B-21467 Mounting Bracket with Mounting Hardware

• Forward-Reverse-Stop Push Button Kit, Remote Mounted

			• Up-Down-Stop Push Button Kit, Remote Mounted
	EA-000003.......................................	$440.67	• Up-Down-Stop Push Button Kit, Remote Mounted
	Includes: 033.1965 Push Button Station, Reversing, Nema1, B-21467 Mounting Bracket with Mounting Hardware			EA-000004.......................................	$440.67
				Includes: 033.1975 Up Down Stop Push Button Station, Reversing, Nema 1, B-21467 Mounting Bracket with Mounting Hardware


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station				• “Start-Stop”Push-button Station
033.1955			$211.23		033.195.................................................	$142.50
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Fwd-Rev-Stop” Push-button Station				• “Fwd-Rev-Stop”Push Button Station
033.1965			$397.05		033.196..................................................	$490.95
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Up-Down-Stop” Push-button Station				OPTIONAL STARTER CONTROLS
033.1975			$397.05	OPTIONAL STARTER CONTROLS
033.1975			$397.05	• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1				• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1					EA-011 ............................................ Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), and a Control Circuit Transformer (As Required), & Pushbutton Station (033.195).	$3,210.68
						$3,210.68

IMPORTANT NOTES
• Control Circuit Transformer Included for 115 Volt Control Voltage. • Above starters are in Nema 3, 4 and 12 Enclosures. • The starters included Safety Disconnect, Overload Relay, and Aux. Contacts as required. • IF AN ORDER IS SUPPLIED LESS MOTOR, AND IS SUPPLYING ANY ELECTRICAL CONTROLS, THEN MOTOR HP, VOLTAGE, PHASE, AND FULL LOAD CURRENT MUST BE STATED ON THE ORDER. • PRICING LISTED IS NOT MOUNTED OR WIRED.

				• Auto Restart Control, 1 Phase, Non-Reversing
					EA-012 (115 Volt) ........................... EA-017 (230 Volt) ........................... Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), Pushbutton Station (033.195), and (230 V. Only) a Control Circuit Transformer (As Required). Note: Above Price does NOT include Photo Eye Mounting Bracket.	$3,253.63
						$3,391.27

• Add on	$192.70	for the above Push Buttons
to be Mounted.
• Add on	$995.10	for the above Starters and
Push Button Stations to be Mounted and Wired. Supply 20'0" of cable for push button only.

				• Mounting Brackets for photo eye
				• Mounting Brackets for photo eye
					#033.2122 B-05165 ..............................................
						$118.10

CONVEYOR WEIGHT TABLE

SIZE TO ORDER Overall Length "A"	Bed Length "L"	Belt Width	12"	18"	24"
SIZE TO ORDER Overall Length "A"	Bed Length "L"	Bed Width	16"	22"	28"
6'-1"	5'	WEIGHTS (Lbs.)	299	322	365
11'-1"	10'		368	415	465
16'-1"	15'		461	525	593
21'-1"	20'		530	608	693
26'-1"	25'		623	718	821
31'-1"	30'		692	801	921
41'-1"	40'		854	994	1149
51'-1"	50'		1023	1197	1391
61'-1"	60'		1185	1390	1609
71'-1"	70'		1355	1594	1862
81'-1"	80'		1517	1787	2090
91'-1"	90'		1697	1979	2319
101'-1"	100'		1841	2172	2547

All weights are conveyor weights only.

Accessories, crating, etc., are not included.

Belt Conveyors, Conveyor, Conveyor Belt, Wire Mesh Belt Conveyor, Wire Belt, Incline Conveyor, Parts Conveyor, Conveyors, and
Mesh Belt from your source for material handling equipment.

Back to Product Category

Home - Order - Search - Quote - Contact Us - About Us - My Account - Shopping Cart

MODEL TW

HORIZONTAL WIRE MESH BELT CONVEYOR

Belt Conveyors, Conveyor, Conveyor Belt, Wire Mesh Belt Conveyor, Wire Belt, Incline Conveyor, Parts Conveyor, Conveyors, and Mesh Belt from your source for material handling equipment.

HORIZONTAL WIRE MESH
BELT CONVEYOR

Belt Conveyors, Conveyor, Conveyor Belt, Wire Mesh Belt Conveyor, Wire Belt, Incline Conveyor, Parts Conveyor, Conveyors, and
Mesh Belt from your source for material handling equipment.