Belt Conveyors, Conveyor, Conveyor Belt, Horizontal Belt Conveyor, Conveyors

ENGINEERED STEEL PRODUCTS

Priced Full Line Products Catalog

20 Technology Way • West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401) 421-5679

Back to Product Category

MODEL PSB PLASTIC BELT CONVEYOR


		The Model PSB with modular plastic belting uses a positive drive system to eliminate belt slippage and mistracking.

		• 16 Belt Widths • Polypropylene 2” Pitch Plastic Belt • Adjustable MS-Type Floor Supports Available

LOAD CAPACITY CHART @65 FPM

HP	16” TO 28” OVERALL WIDTH
	TOTAL LOAD (LBS.)
	UP TO 50’
1/2	750
1	1750
2	3750


Standard Specifications

END DRIVE–Located on discharge end of conveyor. Chain guard located on left hand side.		SNUB ROLLERS–Located at drive and tail ends.

		RETURN BARS–UHMW on aluminum.
		RETURN BARS–UHMW on aluminum.
BELT–Polypropylene 2 in. pitch Flush Grid, nominal 1 in. less than BR.
		BEARINGS–Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts.

BED–UHMW on aluminum slider bars, mounted to frame spacers. Mounted in 7 1/2 in. x 12 ga. powder painted, formed steel channel frame bolted together with butt couplings.
		SPEED REDUCTION–Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket.

		MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face.

CROSS BRACING–Rods with turnbuckles are fastened to underside of bed to provide alignment of bed sections to insure correct belt tracking. Supplied on every other section 30 ft. bed lengths and over.

		BELT SPEED–Constant 65 FPM.

		CAPACITY–Maximum load per linear foot of conveyor 200 lbs. NOT TO EXCEED capacity in chart.


DRIVE AND TAIL SPROCKETS–10 tooth 6.4 in. pitch dia. molded plastic sprockets on 1 1/2 in. sq. shaft, 1 3/16 in. dia. shaft at bearings.


Optional Equipment

FLOOR SUPPORTS–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support.		O-RING DRIVE CHAIN–With sealed in lubricant (Recommended for applications that do not permit regular lubrication).

		CEILING HANGARS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.

BED–Stainless steel in lieu of powder painted HRS (Excluding Aluminum Support Bars).
		NOSEOVER AND NOSEUNDER–Can be in- corporated to provide continuous belt travel from horizontal to incline or decline.

BELT–Other belts available, contact us.

BELT SPEED–Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM and with variable speeds. Note: Capacity affected with speed change.		MOTORS–Energy efficient, single phase, brakemotor, other haracteristics. 2 HP maximum.

		ELECTRICAL CONTROLS–One direction magnetic starters and push-button stations. AC Variable Frequency Drive.


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.


PRICES FOR COMPLETE CONVEYOR INCLUDE:

• Polypropylene 2 in. pitch flush grid • 7 1/2 in. x 12 ga. powder painted, formed steel channel frame with UHMW on aluminum slider bars • 6.4” Pitch Dia. x 20 tooth Drive & Tail Sprockets • “C” Face Speed Reducer–Sealed Worm Gear • 1/2 HP–“C” Face Totally Enclosed Motor (Specify Exact Voltage)		• Totally Enclosed Chain Guard • 65 FPM Belt Speed • Less Electrical Controls • Less Supports

PRICING FOR PSB Plastic Belt Conveyor
SIZE TO ORDER Overall Length "A"	Plastic Belt Widths
	8"	10"	12"	14"	16"	18"	20"	22"
	Overall Bed Widths
	12"	14"	16"	18"	20"	22"	24"	26"
10'-0"	$4,692	$5,067	$5,442	$5,816	$6,192	$6,566	$6,941	$7,316
Per Foot	$235.30	$267.50	$298.60	$329.70	$360.80	$392.90	$422.90	$455.10

SIZE TO ORDER Overall Length "A"	Plastic Belt Widths
	24"	26"	28"	30"	32"	34"	36"	38"
	Overall Bed Widths
	28"	30"	32"	34"	36"	38"	40"	42"
10'-0"	$7,691	$8,066	$8,442	$8,816	$9,191	$9,565	$9,940	$10,315
Per Foot	$487.30	$517.30	$549.50	$580.50	$611.60	$642.70	$672.70	$703.70

IMPORTANT NOTES

• OTHER LENGTHS
For lengths longer or shorter than those shown in chart, use per foot price.
• OTHER WIDTHS
For widths less than 12” OAW , use 12” OAW price plus 10%. For widths over 42” OAW, and up to
60” OAW, interpolate plus 25%.

• FLOOR SUPPORTS
There are two (2) stationary floor supports required for the first bed section and one (1) support per bed
section thereafter.

• NON-STANDARD WIDTHS
Contact us for lead time.


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

MOTORS

Extra Motor Price for OTHER THAN: 1/2 HP–208/230/460/575 V–3 Ph.–60 Hz.–Totally Enclosed.
Speed affects horsepower requirements.

H.P. REQ.	TOTALLY ENCLOSED			ENERGY EFFICIENT		BRAKEMOTORS
H.P. REQ.	200/208/230/ 460/575V 3 Ph.-60 Hz.	115/230V 1 Ph.-60 Hz.	230/460V 3 Ph.-60 Hz.	575V 3 Ph.-60 Hz.	Holding Brake 208/230/ 460/575V 3 Ph.-60Hz.	Cycling Brake 208/230/ 460/575V* 3 Ph.-60Hz.	Cycling Brake 208/230/ 460/575V* 3 Ph.-60Hz.	Holding Brake 115/230V 1 Ph.-60Hz.
1/2	N/C	$39.30	$389.80	$400.90	N/A	N/A	N/A	N/A
1	N/A	$498.10	$498.10	$498.10	$1,051.40	$1,891.10	$3,648.50	$1,219.30
2	N/A	$1,206.80	$972.10	$972.10	$1,639.70	$2,421.60	$3,900.00	$3,154.60

*575V - Prices coded in light blue call for lead time.

* NOTE: "High Cycle Brakemotors" are used for indexing and are rated for 30 cycles per minute. Add-On Prices Include 5AC Reducer,
Heavy Duty Motor Base Plate, and #60 Chain and Sprockets with Taper Bushed Hubs.
** NOTE: "High Cycle Brakemotor" Add-On Prices Include 5AC Reducer, Heavy Duty Motor Base Plate and Timing Belt Drive.
NOTE: SSB and D Series are Holding Brakes and are NOT rated for cycling.

FLOOR SUPPORTS

OPTIONAL DRIVES

Not Included in Base Price. Use Chart Below for
Required Elevation.

Optional Drives
Drive Type	12"-20"	22"-30"	32"-42"
End Drive (V-Belt)	$246.50	$246.50	$246.50
Side Mounted (C-Face)	$245.40	$427.70	$482.20
Side Mounted (V-Belt)	$617.40	$674.20	$728.40
Center (C-Face)	$1,354.00	$1,692.20	$2,031.10
Center (V-Belt)	$1,600.30	$1,938.60	$2,277.50
Overhead (C-Face)	$552.60	$628.40	$704.30
Overhead (V-Belt)	$798.90	$874.90	$950.40

MS SUPPORT
Model No.	Adjustment to Top of Belt	Price each
*MSL-1	9 3/4" to 10 3/4"	$52.60
*MSL-2	10 3/4" to 12 1/2"	$52.60
*MSL-3	12 1/2" to 15 1/8"	$52.60
*MS-1	14 3/4" to 16 1/2"	$52.60
*MS-1.2	15 3/4" to 17 1/2"	$52.60
*MS-1.4	16 3/4" to 18 1/2"	$52.60
*MS-2	17 3/4" to 20 3/4"	$54.40
MS-3	20 3/8" to 23 3/8"	$59.80
MS-4	23 3/8" to 29 3/8"	$68.80
MS-5	27 3/8" to 33 3/8"	$71.90
MS-6	31 3/8" to 43 3/8"	$79.40
MS-7	41 3/8" to 53 3/8"	$117.30
MS-8	53 3/8" to 65 3/8"	$133.80
MS-9	65 3/8" to 77 3/8"	$146.70
MS-10	77 3/8" to 89 3/8"	$167.20
MS-11	87 3/8" to 99 3/8"	$184.90
MS-12	99 3/8" to 111 3/8"	$193.30

#50 O-Ring Drive Chain............Add ........ $284.40

GUARD RAILS*

Adjustable Universal Channel Guard Rail

Both Sides .................. per foot ................. $15.10

One Sides .................. per foot .................. $7.80

Angle Type

Types “A” or “B” available (specify).
Prices are for both sides.

Type “A”
1 1/2” x 1 1/2” x 12 Ga.......... per foot............... $7.80

*Less than 19 15/16" top of belt elevation -

Type “B” (See NOTE)
1 1/2” x 1 1/2” x 12 Ga.......... per foot............... $10.90

Side mounted Drive Required

NOTE: MS-7 to MS-12: Knee Braces included in price

Extra Knee Braces .......... per pair....................................... $30.00

Fixed Channel Type
(Prices are for both sides.)

Single Center Leg (MSC-6 and below) each.................... $60.40

Single Center Leg (MSC-7 and above) each.................... $75.10

3 1/2” x 1 1/2” x 12 Ga........... per foot............. $22.50

* NOTE: If product comes in contact with guard rails, product
flow will be affected.


CEILING HANGERS		CONSTANT AND VARIABLE SPEEDS
Ceiling Hanger Brackets with (2) 5/8" dia. x 8'-0" long unplated fully threaded rods.........		Constant C-Face–Within 15-70 FPM....No Charge
	$147.90	Constant V-Belt–Minimum of 4 FPM........ .................................Use V-Belt Drive Add-On
Ceiling Hanger Brackets with (2) 5/8" dia. x 8'-0" long galvanized fully threaded rods.......
	$176.60
	$176.60	DRIVE COMPONENT DEDUCTS
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully threaded rods.....		DRIVE COMPONENT DEDUCTS
		Less Motor Drive, Motor Mount and Guards, but with Shaft Extension and Sprocket ....... Deduct ................................................. $694.20
	$218.40
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods....
	$359.60
	$359.60	Less Motor Only (1/2 HP-208/230/460/575 V- 3 Ph.-60 Hz.) ..... Deduct....................... $258.30
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.....
	$362.60
	$362.60	Less Reducer...............Deduct............. $307.40*
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods....		Less Reducer...............Deduct............. $307.40*
		*Less V-Belt Guard, Chain Guard, sheaves and sprockets when V-Belt drive is supplied. Less chain guard and sprockets when C-Face drive is supplied.
	$419.40
Ceiling Hanger Brackets, Less Rods Only....	$93.10
Extra Length Rods:

		CENTER BEARING SUPPORT (END DRIVE)
(2) 8’-0” long x 5/8” dia. unplated fully threaded rods ............................................		CENTER BEARING SUPPORT (END DRIVE)
		(Drive and Tail) ..............Add On........... $676.10
	$54.20
	$54.20
(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods .............................................		GALVANIZING - Contact us.
	$83.40	GALVANIZING - Contact us.
	$83.40
		POLY-TIER SUPPORTS
(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ..............................................		POLY-TIER SUPPORTS
	$125.20		PRICES FOR COMPLETE CONVEYOR INCLUDE: • Painted Steel Support Legs • Adjustable Crosspipe Assembly • Knee Braces (1 set per level of conveyor) • “U” Brackets • Single Width Conveyor Only

(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods ..............................................
	$266.30
(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ..............................................
	$269.60
(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods ..............................................
	$326.50
	$326.50		IMPORTANT NOTES. . . • Check for Clearance. • Specify type of conveyor to be used. • Use in place of LS or MS Supports only.
Hex Coupling Nuts for Rods ...................	$4.90
Hex Coupling Nuts for Rods ...................	$4.90

			CAPACITY DATA: 1500 lbs. ...........per cross pipe 4500 lbs. ...........per set of legs

(2) TIER POLY-TIER SUPPORTS
36"	$311.36
42"	$320.01
48"	$328.56
54"	$337.00
60"	$345.65
66"	$354.42
72"	$362.86
78"	$371.52
84"	$380.00
90"	$388.50
96"	$397.27
102"	$405.93
108"	$414.60
114"	$423.69
120"	$431.46

(3) TIER POLY-TIER SUPPORTS
36"	$439.01
42"	$447.80
48"	$456.30
54"	$464.80
60"	$473.42
66"	$482.18
72"	$490.62
78"	$499.30
84"	$507.80
90"	$516.40
96"	$524.90
102"	$533.60
108"	$542.46
114"	$550.45
120"	$559.00


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

ELECTRICAL CONTROLS AND DRIVE SECTION

MANUAL START SWITCH or
SAFETY DISCONNECT

LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER

#032.1014.........................................

$213.01

#033.2032 & #033.2072..................$555.67
Nema 4

"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)

LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER

#033.2033& #033.2072...................$332.11
Nema 4

REVERSING DRUM SWITCH

#032.103..........................................

$854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase

PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range

FOOT SWITCH WITH GUARD

#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range

#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.

PHOTO EYE, ON-OFF TYPE

#EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC

POWER CORD AND PLUG (20')

POWER CORD WITH PLUG ONLY 20' LONG
Model No.	Voltage	HP Rating	Prices
EA-039-1A	115/1	1/2-3/4	$106.67
EA-039-2A	115/1	1	$106.67
EA-039-3A	115/1	1 1/2	$155.18
EA-039-4A	230/1	1/2-1	$106.67
EA-039-5A	230/1	1 1/2-2	$109.67
EA-039-6A	208-230/3	1/2-2	$178.60
EA-039-7A	460/3	1/2-2	$178.60

POWER CORD WITH PLUG 20' LONG WITH MANUA
Model No.	Voltage	HP Rating	Prices
EA-039-1B	115/1	1/2-3/4	$173.16
EA-039-2B	115/1	1	$330.67
EA-039-3B	115/1	1 1/2	$377.96
EA-039-4B	230/1	1/2-1	$293.04
EA-039-5B	230/1	1 1/2-2	$330.67
EA-039-6B	208-230/3	1/2-2	$362.97
EA-039-7B	460/3	1/2-2	$362.97

MOUNTING BRACKETS FOR PHOTO
EYE #033.2122

B-05165...........................................$118.10

AIR PRESSURE SWITCH

#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH

#032.285 with 032.2851 Turnbuckle
...........................................................$696.08
Nema 4

"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE

#032.281...one side.................$7.44 per / ft.
both sides..............$15.87per / ft.

EMERGENCY PUSH BUTTON

#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE

#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48

NOTE: PRICING LISTED NOT MOUNTED
OR WIRED

"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC

#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

CONTROLLER PRICES

AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size	115 Volt		208/230 Volt
1/2	VSC-12-10		VSC-12-12
Price	$1,491.84		$1,189.37
1	VSC-12-11		VSC-12-13
Price	$1,724.27		$1,391.05
2	N/A		VSC-12-14
Price	~		$1,794.20
THREE PHASE CONTROLLER INPUT
Motor Size	208/230 Volt	460 Volt	575 Volt
1/2	VSC-01-15	VSC-01-18	VSC-12-29
Price	$1,564.99	$1,656.34	$2,155.73
1	VSC-01-16	VSC-01-19	VSC-12-29
Price	$1,579.75	$1,794.20	$2,155.73
2	VSC-01-17	VSC01--20	VSC-12-30
Price	$1,978.69	$2,070.37	$2,663.45

REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS

HP	Part No.	Price
1/2	032.351 230/460	$618.71
1	032.353 230/460	$705.52
2	032.355 230/460	$797.31
1/2	032.3512 575	$1,449.11
1	032.3532 575	$1,611.17
2	032.3552 575	$1,897.10

IMPORTANT NOTES...

• All above motors are 230 / 460 / 575 Volt, 3 Phase.
• All above V/S Drive Kits include NEMA 1 / IP30
Junction Box, Controller and Motor.
• Good for cycle rates of up to 15 cycles per minute, at
1/2 second ramp time, with a maximum speed of 250
FPM.
• Drawing No. DG-001146.

OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)

$675.20

• When AC Variable Speed Controller is used with a
Brake Motor, A Brake Relay Kit (EA-068A) is
required. Add an additional $542.68 for this option.)

Brake Relay Kit (EA-068A)..............................

$542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE

Part No.	Description	Price
EA-VSC-01-CB	2 HP Electronic Clutch-Brake Kit	$5,058.00

OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)

$675.20

KIT INCLUDES

Part No.	Description
VSC-01-20	AC Variable Speed Controller, 460 Volt, 3 Phase
032.345	2 HP 460 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

IMPORTANT NOTES

• Good for cycle rates of up to 60 cycles per minute.
• 1/10 second Accel and Decel time, with 350 FPM
Maximum Speed.
• 230 or 460 Volt Only, Other Voltages, Contact us.
• Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
• Price Includes 5AC Reducer and #60 Chain and
Sprockets

Part No.	Description
VSC-01-17	AC Variable Speed Controller, 230 Volt, 3 Phase
032.345	2 HP 230 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)

An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.

THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	MOTOR DUTY	NON-REVERSING					REVERSING
H.P.	MOTOR DUTY	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE
1/2	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B25	EN-46B16	EN-57B10	$1516.60	ER-20B40	ER-23B25	ER-46B16	ER-57B10	$2,023.30
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B16	EN-46B10				ER-23B16	ER-46B10
1	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B40	EN-46B25	EN-57B16		ER-20B40	ER-23B40	ER-46B25	ER-57B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
1-1/2	GEARMOTORS	EN-20C10	EN-23B63	EN-46B40	EN-57B25		ER-20C10	ER-23B63	ER-46B40	ER-57B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
2	STANDARD EASY CLEAN ENERG. EFF.	EN-20C10	EN-23C10	EN-46B40	EN-57B40		ER-20C10	ER-23C10	ER-46B40	ER-57B40
			EN-23C10	EN-46B40				ER-23C10	ER-46B40
			EN-23B63	EN-46B40				ER-23B63	ER-46B40

SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	NON-REVERSING		REVERSING		NON-REVERSING		REVERSING
	115 VOLT	PRICE	115 VOLT	PRICE	230 VOLT	PRICE	230 VOLT	PRICE
1/2	EN-1SC10	$1,182.40	ER-1SC10	$2,023.30	EN-2SB63	$1,435.60	ER-2SB63	$2,023.30
1	EN-1SC16		ER-1SC16		EN-2SC10		ER-2SC10
1-1/2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10
2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10


• Manual Start-Stop Switch Kit			• Start-Stop Push Button Kit, Remote Mounted
	EA-000001 ......................................	$242.09		EA-000002.......................................	$242.09
	Includes: 032.1014 Manual Start Switch, Nema 1, B-21467 Mounting Bracket with Mounting Hardware			Includes: 033.1955 Push Button Station, One Direction, Nema1, B-21467 Mounting Bracket with Mounting Hardware

• Forward-Reverse-Stop Push Button Kit, Remote Mounted

			• Up-Down-Stop Push Button Kit, Remote Mounted
	EA-000003.......................................	$440.67	• Up-Down-Stop Push Button Kit, Remote Mounted
	Includes: 033.1965 Push Button Station, Reversing, Nema1, B-21467 Mounting Bracket with Mounting Hardware			EA-000004.......................................	$440.67
				Includes: 033.1975 Up Down Stop Push Button Station, Reversing, Nema 1, B-21467 Mounting Bracket with Mounting Hardware


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station				• “Start-Stop”Push-button Station
033.1955			$211.23		033.195.................................................	$142.50
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Fwd-Rev-Stop” Push-button Station				• “Fwd-Rev-Stop”Push Button Station
033.1965			$397.05		033.196..................................................	$490.95
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Up-Down-Stop” Push-button Station				OPTIONAL STARTER CONTROLS
033.1975			$397.05	OPTIONAL STARTER CONTROLS
033.1975			$397.05	• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1				• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1					EA-011 ............................................ Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), and a Control Circuit Transformer (As Required), & Pushbutton Station (033.195).	$3,210.68
						$3,210.68

IMPORTANT NOTES
• Control Circuit Transformer Included for 115 Volt Control Voltage. • Above starters are in Nema 3, 4 and 12 Enclosures. • The starters included Safety Disconnect, Overload Relay, and Aux. Contacts as required. • IF AN ORDER IS SUPPLIED LESS MOTOR, AND IS SUPPLYING ANY ELECTRICAL CONTROLS, THEN MOTOR HP, VOLTAGE, PHASE, AND FULL LOAD CURRENT MUST BE STATED ON THE ORDER. • PRICING LISTED IS NOT MOUNTED OR WIRED.

				• Auto Restart Control, 1 Phase, Non-Reversing
					EA-012 (115 Volt) ........................... EA-017 (230 Volt) ........................... Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), Pushbutton Station (033.195), and (230 V. Only) a Control Circuit Transformer (As Required). Note: Above Price does NOT include Photo Eye Mounting Bracket.	$3,253.63
						$3,391.27

• Add on	$192.70	for the above Push Buttons
to be Mounted.
• Add on	$995.10	for the above Starters and
Push Button Stations to be Mounted and Wired. Supply 20'0" of cable for push button only.

				• Mounting Brackets for photo eye
				• Mounting Brackets for photo eye
					#033.2122 B-05165 ..............................................
						$118.10

CONVEYOR WEIGHT TABLE

MODEL PSB PLASTIC BELT CONVEYOR

SIZE TO
ORDER
overall
Length

Belt Width

10"

12"

14"

16"

18"

20"

22"

24"

26"

28"

30"

32"

34"

36"

38"

Between Rail
Width

11"

13"

15"

17"

19"

21"

23"

25"

27"

29"

31"

33"

35"

37"

39"

Overall Frame
Width

12"

14"

16"

18"

20"

22"

24"

26"

28"

30"

32"

34"

36"

38"

40"

42"

10'

Weights

328

248

368

388

408

428

448

468

488

508

528

548

568

588

608

628

WeightsPerFoot

Belt Conveyors, Conveyor, Conveyor Belt, Low Profile Conveyor, Conveyors, and Slider Bed from your source for material handling
equipment.

Back to Product Category

Home - Order - Search - Quote - Contact Us - About Us - My Account - Shopping Cart

MODEL PSB PLASTIC BELT CONVEYOR

Belt Conveyors, Conveyor, Conveyor Belt, Low Profile Conveyor, Conveyors, and Slider Bed from your source for material handling equipment.

Belt Conveyors, Conveyor, Conveyor Belt, Low Profile Conveyor, Conveyors, and Slider Bed from your source for material handling
equipment.