FS Industries ENGINEERED STEEL PRODUCTS
Priced Full Line Products Catalog
20 Technology Way West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401) 421-5679
Home Order Search Quote Contact Us About Us My Account Shopping Cart
Back to Product Category

MODEL 25-CRR

CHAIN DRIVEN LIVE ROLLER CONVEYOR
(Roll-to-Roll Type)

chain driven live roller conveyor The heavy design of the 25-CRR
allows it to be used for conveying
higher load capacities such as loaded
pallets and drums. Chain driven rollers
make it ideal for conveying oily parts
in bottling and steel industries.
• 15 Bed Widths
• Center Drive
• Reversible
• Chain Driven Rollers
• Adjustable HSN-Type Floor Supports
   Available

roller conveyor
LOAD CAPACITY CHART @ 30 FPM
HP
TOTAL LOAD (LBS.)
UP TO 50'
UP TO 100'
1
9000
6000
2
22000
18000
NOTE: Capacities are calculated on 5" Roller Centers
with #50 Chain.
STANDARD SPECIFICATIONS
BED - Roller bed with 2-1/2 in. dia. x 11 ga. unplated
tread rollers spaced every 4 in. with No. 40 roller chain;
5 in. with No. 50 roller chain. No. 60 roller chain used
on 3 in., 3-3/4 in., 6 in., and 7-1/2 in. roller centers only.
Tread rollers mounted in 4 in. x 4 ga. powder painted
formed steel channel on side opposite chain guard and
6 in. x 4 ga. powder painted formed steel channel on
chain guard side. NOTE: 3 in. roller center tread rollers
mounted in 4 in. channel each side.
BEARINGS–Sealed, pre-lubricated ball bearings.
SPEED REDUCTION–Sealed worm gear C-Face
speed reducer.
MOTOR–1 HP–208/230/460/575V–3 Ph. 60 Hz.
Totally Enclosed C-Face.
CONVEYING SPEED–Constant 30 FPM.
CAPACITY–Maximum load per linear foot of conveyor
300 lbs. with supports on 10 ft. centers, 1000 lbs. with
supports on 5 ft. centers. Contact us for capacity
of No. 40 chain, 4 in. roller centers. NOT TO EXCEED
CAPACITY IN CHART.
CENTER DRIVE- Can be placed in any section of
conveyor length, specify. Chain guard located on left
hand side.
DRIVE CHAIN–No. 40, 50 or 60 roller chain.
FLOOR SUPPORTS–Now supplied as optional
equipment.
CHAIN GUARD–Formed steel, upper and lower
chain guard mounted to top and bottom of channel
frame to totally enclose drive chains.

OPTIONAL EQUIPMENT
FLOOR SUPPORTS–HSN Type floor supports are
available with a wide range of adjustment. Specify top
or roller elevation. One support required at every bed
joint and ends of conveyor. Holes in feet for lagging to
floor. Knee braces recommended above HSN-3
support.
CHANNEL END STOP–6” x 8.2 lb. structural channel
end stop.
ROLLERS SET LOW–Tread rollers mounted in 5 in.
x 4 ga. formed steel channel frame to form 5/8 in. high
guard rails. Also available in 5 in. x 6.7 lbs. structural
channel frame (welded). Specify.
CONVEYING SPEED–Other constant and variable
speeds. V-belt supplied on speeds under 12 FPM
(1 HP). NOTE: Capacity affected with speed change.
CHAIN CROSSOVER–Separate 3-roller section
moves driving chain from one side of conveyor to other.
Offset-style adds 12 in. to OAL of conveyor with No.
40 chain, 15 in. with No. 50 chain & 18 in. with No.60
chain.
TOP SIDE MOUNTED DRIVE–Motor reducer
unit mounted to side of conveyor with drive chain
through top of chain guard. Specify clearances.
Minimum elevation top of rollers 6 in.
TRANSFERS–Chain transfers available. See
Accessory section.
V-BELT DRIVE–V-belt supplied between motor
and reducer.
MOTORS–Energy efficient, single phase, brake motor,
other characteristics. 2 HP maximum.
O-RING DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit
regular lubrication).
ELECTRICAL CONTROLS–Non-reversing
magnetic starter – pushbutton stations. AC variable
frequency drive.
FRAMES–4 in. x 5.4 lb. structural channel (welded).
GUARD RAILS–Fixed angle (2 in. high x 1/4 in.
steel) guard bolts to top flange of channel opposite
chain guard.

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


PRICES FOR COMPLETE CONVEYOR INCLUDE:
• 2-1/2” Dia. x 11 Ga. Roller Mounted in a 4” x 4 Ga. Formed Channel Frame
• No. 40 *, No. 50, or No. 60 Roller Chain
• “C” Face Speed Reducer—Sealed Worm Gear
• 1 HP–“C” Face Totally Enclosed Motor (Specify Exact Voltage)
• Totally Enclosed Chain Guard
• 30 FPM Conveying Speed
• Less Electrical Controls
• Less Supports
4 in., 5 in., 6 in. and 7-1/2 in. Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 19" 21" 23" 25" 27" 31" 33" 37" 39" 43" 47" 51" 55" 61" 67"
Overall Frame Width 22-1/4" 24-1/4" 26-1/4" 28-1/4 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
*4" Centers
10' Length-
O.A. Per Foot
No. 40
Chain
5" Centers
10' Length-
OA Per Foot
No.50
Chain
6" Centers
10' Length-
OA Per Foot
No. 60
Chain
7-1/2" Centers
10' Length-
OA Per Foot
No. 60
Chain
3 3/4 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22" 24" 26" 28" 30" 34" 36" 40" 42" 46" 50" 54" 58" 64" 70"
Overall Frame Width 25-1/4" 27-1/4" 29-1/4" 31-1/4" 33-1/4" 37-1/4" 39-1/4" 43-1/4" 45-1/4" 49-1/4" 53-1/4" 57-1/4" 61-1/4" 67-1/4" 73-1/4"
3 3/4" Centers
10' Length-
OA Per Foot
No. 60
Chain
3 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22-1/4" 24-1/4" 26-1/4" 28-1/4" 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4" 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
Overall Frame Width 25-1/2" 27-1/2" 29-1/2" 31-1/2" 33-1/2" 37-1/2" 39-1/2" 43-1/2" 45-1/2" 49-1/2" 53-1/2" 57-1/2" 61-1/2" 67-1/2" 73-1/2"
3" Centers
10' Length-
OA Per Foot
No. 60
Chain
#60 Chain with Chain Guard on Both Sides
3 in Roller Centers Chain Guard One Side
Conveying Surface 17-3/4" 19-3/4" 21-3/4" 23-3/4" 25-3/4" 29-3/4" 31-3/4" 35-3/4" 37-3/4" 41-3/4" 45-3/4" 53-3/4" 59-3/4" 63-3/4" 65-3/4"
Between Rail Width 22" 24" 26" 28" 30" 34" 36" 40" 42" 46" 50" 58" 64" 68" 70"
Overall Frame Width 25-1/4" 27-1/4" 29-1/4" 31-1/4" 33-1/4" 37-1/4" 39-1/4" 43-1/4" 45-1/4" 49-1/4" 53-1/4" 61-1/4" 67-1/4" 71-1/4" 73-1/4"
3" Centers
10' Length-
OA Per Foot
No. 40
Chain
*No. 40 Chain reduces total conveyor capacity.
IMPORTANT NOTES

• OTHER LENGTHS
   For longer or shorter than 10’ Overall Length, add or deduct PER FOOT from 10’ price. NO DEDUCT for unit
   less than 5’.
• CHAIN GUARD END CAPS
  Add 1-3/8" to OAL for Chain Guard End Caps on 4" centers only. Add 3" to OAL For Chain Guard End Caps
  on 3" roller centers only.
• OTHER WIDTHS
   For “IN-BETWEEN WIDTHS”, use next width plus 10%. For widths up to 74-1/4” OAW, interpolate plus 10%.
   For widths over 74-1/4” OAW, contact us for lead time.
• INTERMEDIATE BEDS
  Use per foot price of width x required length, supports not included.
• FLOOR SUPPORTS
  Floor Supports are not included in base price. There are two (2) stationary floor supports required for the first
  bed section and one (1) support required per bed section thereafter.
• NON-STANDARD WIDTHS
 
Contact us for lead time.


Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


PRICES FOR OPTIONAL EQUIPMENT
MOTORS
Extra Motor Price for OTHER THAN: 1 HP-208/230/460/575 V-3 Ph.-60 Hz.-Totally Enclosed. Speed affects
horsepower requirements.
H.P. REQ.
TOTALLY ENCLOSED
ENERGY
EFFICIENT
200/208/230/460/575V 3Ph-60Hz.
115/230V 1Ph-60Hz
1
N/C $83.60
2
$936.80 $1,142.20
FLOOR SUPPORTS DRIVE COMPONENT DEDUCTS
Not Included in Base Price. Use Chart Below for
Required Elevation.
Less Complete Motor Drive and Drive Shell (For
Slave Driving) ........... Deduct.................... $982.00
Less Motor Only (1 HP-208/230/460/575 V-3
"HSN" SUPPORT
Model No. Adjustment to
Top of Roller
Price Up to
73 1/4" OAW
Price Above
74 1/4" OAW
HSN-1** 10-1/2" to 12"
HSN-2** 12" to 15"
HSN-3** 15" to 18"
HSN-4* 18" to 21"
HSN-5* 21" to 24"
HSN-6* 24" to 30"
HSN-7* 30" to 36"
HSN-8* 36" to 48"
HSN-9* 48" to 60"
HSN-10* 60" to 72"
HSN-11* 72" to 84"
HSN-12* 84" to 96"
Ph.-60 Hz.) ............... Deduct .................. $282.90
Less Reducer* (4A or 4AC) Deduct ........ $307.40
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less
chain guard and sprockets when C-Face drive is
supplied.
GUARD RAILS
Angle Type “A”
2” x 1-5/8” x 1/4”
Side Opposite Chain Guard ... per foot .........
$11.40
CONSTANT AND VARIABLE SPEEDS
Constant C-Face–Within 16-75 FPM .............
.........(#60 Chain) ....................................No Charge
Constant C-Face–Within 14-75 FPM .............
.........(#40 and #50 Chain) .......................No Charge
Constant V-Belt–Within 4-12 FPM .....................
............................... Use V-Belt Drive Add-on
* Knee Braces (Included in support price)
   Extra Braces ......Add per pair ................... $72.80
**Less than 18-1/2” top of roller elevation–
   Top Side Mounted Drive Required.
OPTIONAL FRAME
6” x 1-5/8” x 4 Ga. Formed Channel Set Low .....
OPTIONAL DRIVE ............................... add on per foot ........ $5.70
Drive
Type
Overall Frame Width
22-1/4" to
34-1/4"
36-1/4"
to 54-1/4"
58-1/4"
to 70-1/4"
Top Side
Mounted C-Face
Top Side
Mounted V-Belt
Shaft Mounted
Drive
4” x 5.4 lbs. Structural Channel ........................
............................... add on per foot ........ $13.50
5” x 6.7 lbs. Structural Channel Set Low (Welded)...
............................... add on per foot ........ $17.30
6” x 8.2 lbs. Structural Channel Set Low (Welded)...
............................... add on per foot ........ $32.60
HEAVY DUTY END STOP (SET HIGH ONLY)
6” x 8.2 lbs. structural channel
19” - 43” BR ............................................ $100.20
#50 O-Ring Drive Chain ......... Add ......... $284.40
45” - 67” BR ............................................ $146.40
#60 O-ring Drive Chain ......... Add ......... $406.00
Under 5’ -0” OAL use Top Side Mounted or V-Belt Drive.
HEAVY DUTY END STOP (SET LOW ONLY)
V-Belt Drive. 3'-0" and under use V-Belt Drive ONLY.
7” x 9.8 lbs. structural channel
ELECTRICAL CONTROLS
19” - 43” BR ............................................ $146.50
See below.
45” - 67” BR ............................................ $222.80
CHAIN CROSSOVER GALVANIZING
Off-Set Style “C” or “D” .......................... $1,015.40 Contact us.
chain crossover
ANGLE END STOP
2” x 2” x 4 Ga.
19” - 23” BR ........................................... $42.60
25” - 39” BR ............................................ $56.10
43” - 55” BR ............................................
57” - 67” BR ............................................ $85.25
OPTIONAL ROLLERS
Use the following Add-on prices for optional
roller centers and bearings.
Regreasable Bearings with Grease Fittings
3” Roller Centers ......... Add-on per foot ... $165.80
3-3/4” Roller Centers ... Add-on per foot ... $132.60
4” Roller Centers ......... Add-on per foot .... $124.30
5” Roller Centers ......... Add-on per foot .... $99.40
6” Roller Centers ......... Add-on per foot .... $83.00
7-1/2” Roller Centers ... Add-on per foot ... $66.40
2-1/2" x 7 Ga. with 013.1059 Heavy Duty Bearings
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
3" Centers Add on Per Foot
3-3/4" Centers Add on Per Foot
4" Centers Add on Per Foot
5" Centers Add on Per Foot
6" Centers Add on Per Foot
7-1/2" Centers Add on Per Foot

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole

#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range


foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.


PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10

AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................
$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED
"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
All above motors are 230 / 460 / 575 Volt, 3 Phase.
All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)
$675.20 When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)
Brake Relay Kit (EA-068A).............................. $542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)
$675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
Good for cycle rates of up to 60 cycles per minute.
1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
230 or 460 Volt Only, Other Voltages, Contact us.
Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use
.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware
Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware
EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
$211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
$3,210.68
IMPORTANT NOTES
Control Circuit Transformer Included for 115 Volt
  Control Voltage.
Above starters are in Nema 3, 4 and 12 Enclosures.
The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.
$3,253.63
$3,391.27
Add on $192.70 for the above Push Buttons
  to be Mounted.
Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10

CONVEYOR WEIGHT CHART
4 in., 5 in., 6 in., 7-1/2 in. Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 19" 21" 23" 25" 27" 31" 33" 37" 39" 43" 47" 51" 55" 61" 67"
Overall Frame Width 22-1/4" 24-1/4" 26-1/4" 28-1/4 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
*4" Centers 10' Length-
O.A. Per Foot
No. 40
Chain
722 750 778 806 834 890 918 974 1002 1058 1114 1170 1226 1310 1394
61 64 67 70 73 79 82 88 91 97 103 109 113 124 133
5" Centers 10' Length-
O.A. Per Foot
No. 50
Chain
638 666 694 721 749 804 823 887 915 970 1026 1081 1136 1219 1302
54 57 60 63 66 72 75 81 84 90 96 102 108 117 126
6" Centers 10' Length-
O.A. Per Foot
No. 60
Chain
582 610 638 666 694 750 778 834 862 918 974 1030 1086 1170 1254
49 52 55 58 61 67 70 76 79 85 91 97 103 112 121
7-1/2" Centers 10' Length-
O.A. Per Foot
No. 60
Chain
526 554 582 610 638 694 722 778 806 862 918 974 1030 1114 1198
46 49 52 55 58 64 67 73 76 82 88 94 100 109 118
3 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22-1/4" 24-1/4" 26-1/4" 28-1/4" 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4" 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
Overall Frame Width 25-1/2" 27-1/2" 29-1/2" 31-1/2" 33-1/2" 37-1/2" 39-1/2" 43-1/2" 45-1/2" 49-1/2" 53-1/2" 57-1/2" 61-1/2" 67-1/2" 73-1/2"
3" Centers 10' Length-
OA Per Foot
No. 60 Chain 862 890 918 946 974 1030 1058 1114 1142 1198 1254 1310 1366 1450 1534
72 75 78 81 84 90 93 99 102 108 114 120 126 135 144
3 3/4 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22" 24" 26" 28" 30" 34" 36" 40" 42" 46" 50" 54" 58" 64" 70"
Overall Frame Width 25-1/4" 27-1/4" 29-1/4" 31-1/4" 33-1/4" 37-1/4" 39-1/4" 43-1/4" 45-1/4" 49-1/4" 53-1/4" 57-1/4" 61-1/4" 67-1/4" 73-1/4"
3 3/4" Centers 10' Length-
OA Per Foot
No. 60 Chain 750 778 806 833 861 916 944 999 1027 1083 1137 1193 1249 1332 1415
63 68 71 74 77 83 86 92 95 101 107 113 119 128 137
#40 chain reduces total conveyor capacity. Consult us.
All weights are conveyor weights only. Accessories, crating, etc., are not included.
Note: Add 1-3/8" to OAL for Chain Guard End Caps on 4" centers only.
Note: Add 3" to OAL for Chain Guard End Caps on 3" roller centers only.
Chain Driven Live Roller Conveyor, Roll-to-Roll, Chain Driven Live Roller Conveyors, Conveyor, Live Roller
Conveyors, Powered Live Roller, Conveyors, and Roller Conveyors from your source for material handling equipment.
Back to Product Category
Visa - MasterCard - AMEX
Home - Order - Search - Quote - Contact Us - About Us - My Account - Shopping Cart