 |
ENGINEERED
STEEL PRODUCTS |
| Priced
Full Line Products Catalog |
20
Technology Way • West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401)
421-5679 |
|
|
|
|
Back to Product Category
|
Conveying
Surface |
12
1/4" |
14
1/4" |
16
1/4" |
18
1/4" |
20
1/4" |
22
1/4" |
24
1/4" |
28
1/4" |
30
1/4" |
34
1/4" |
36
1/4" |
Between
Rail Width |
15"
| 17"
| 19"
| 21"
| 23"
| 25"
| 27"
| 31"
| 33"
| 37"
| 39"
|
Overall
Frame Width |
18"
| 20"
| 22"
| 24"
| 26"
| 28"
| 30"
| 34"
| 36"
| 40"
| 42"
|
Weight
(lbs.) Per Foot 4" Roller Centers |
51 |
53 |
55 |
57 |
59 |
61 |
63 |
67 |
69 |
73 |
75 |
Weight
(lbs.) Per Foot 6" Roller Centers |
46 |
48 |
50 |
52 |
54 |
56 |
58 |
62 |
64 |
66 |
68 |
|
Total
Weight = (Number of Zones x 30) + (OAL x Weight Per Foot)
All weights in catalog are conveyor weights only. Accessories, crating,
etc., are not included. |
|
 |
|
 |
|
STANDARD
SPECIFICATIONS |
|
|
|
|
|
|
|
|
BED – Roller bed with 1.9 in. dia. x 9 ga. unplated rollers
spaced every 4 or 6 in. Tread rollers mounted in 3 1/2
in. x 7 ga. formed channel on side opposite chain guard
and 4 3/4 in. x 7 ga. formed channel on chain guard side.
Bolted together with butt couplings. |
|
|
EZLOGIC®
ZONE CONTROLLER–Located in
each zone (Retro-Refl ective). NEMA 1, 2, IP 62.
UL Approved. |
|
|
|
|
|
|
|
IOP–Provides
27VDC, 100 watt power for EZLogic®
accumulation system; contains slots for 4 input/output
boards. Should be located near disconnect panel. See
chart for maximum quantity of zones. Requires 120VAC
or 230VAC single phase input. |
|
|
|
|
|
| DRIVE
CHAIN–No. 40 roller-to-roller. |
|
|
|
|
|
|
|
CHAIN GUARD–Formed steel guards totally enclose
drive chains. |
|
|
|
|
|
|
|
|
|
|
|
|
CONVEYING
SPEED–Constant 35 FPM. |
|
EZDRIVE® SYSTEM – Shaft mounted gearmotor
located near center of each zone. 1/3 HP, 3 Ph, 60
Hz. Totally enclosed fan cooled. 230/460 V (specify
voltage). Includes EZDrive® Disconnect Panel. Power is
distributed zone-to-zone through pluggable cordsets.
Power is connected from the starter box to the motor
via SO type cord. Please contact factory if local code
requires other than the standard power distribution
techniques described. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAPACITY–Maximum load per linear foot of conveyor:
150 lbs. with supports on 10 ft. centers, 250 lbs. per
ft. with supports on 5 ft. centers. Not to exceed 1300
lbs. per zone. Zones longer than 6 ft. may require an
additional floor support depending on product load. |
|
|
|
|
|
|
|
|
|
|
|
FLOOR
SUPPORTS–Supplied as optional
equipment. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Disconnect
Panel |
230V 3 Ph.
60 Hz |
460V 3Ph.
60 Hz |
Single Output |
1-8 Zones |
1-15 Zones |
Dual Output |
9-16 Zones |
16-22 Zones |
|
|
ACCUMULATION
ZONES–4 in. roller centers,
32 in. to 120 in. on 4 in. increments. 6 in. centers,
30 in. to 120 in. on 6 in. increments. Frame length
changes with zone length. |
|
|
|
|
|
Note:
Infeed Wake-Up Eye used only on terminating infeed end of conveyor. Not
used when connecting to upstream
EZLogic® conveyor through power supply isolation cable. |
|
|
|
 |
|
|
|
| EZLOGIC®
ACCUMULATION SYSTEM |
EZLogic®, or Electronic Zero-Pressure Logic Accumulation System, combines
the sensing accuracy
of photo-electronics with discrete electronic logic control without the
use of a PLC or pneumatic logic
components. The EZLogic® Accumulation System provides many features
including: |
Zero-Pressure Accumulation of Product
Zone Stop function is built in. Any zone may be
transformed into a workstation by connecting a dry
contact switching device to the auxiliary port of the
EZLogic® Zone Controller. This feature is always
used at the discharge end of the conveyor line, and
may be used at any other location where a zone stop
is required. |
Sleep Feature – Stops tread rollers from turning when
no product is present, reducing noise, reducing energy
consumption and extending roller bearing life.
Unloading Zone Feature - Zone On Delay – Timer
delays the zone immediately upstream from a removed
load, preventing it from driving for a set time. This
feature is ideal where loads are routinely removed from
the conveyor with a lift truck.
Loading Zone Feature – Zone detects load being
placed onto the conveyor with a fork truck and stops
the zone from driving and automatically prevents any
loads in zones upstream from entering loading area. |
Dynamic Zone Allocation – Automatically adjusts the
conveyor’s zone length to accommodate the length
of the product being conveyed. Improves conveyor
efficiency and system flexibility. |
|
OPTIONAL
EQUIPMENT |
|
|
|
FLOOR
SUPPORTS–MSN Type floor supports are
available with a wide range of adjustment. Specify top
of belt or roller elevation. One support required at every
bed joint and ends of conveyor. Holes in feet for lagging
to floor. Knee braces recommended above MSN-6
support. |
|
POLY-TIER SUPPORTS – 36 in. to 120 in. support
heights in 6 in. increments. Knee braces supplied. |
|
|
|
CEILING HANGER – 5/8 in. dia. x 8 ft. long un-
plated rods fully threaded. Other lengths and gal-
vanized rods available. |
|
|
|
EZDRIVE®
SYSTEM – Variable Frequency Drive
for adjusting conveying speed or adjusting acceleration
and deceleration time. |
|
|
CONVEYING
SPEED–Other constant and variable
speeds. Note: Capacity affected with speed change. |
|
|
|
ROLLERS
SET LOW – Tread rollers mounted in
4 3/4 in. x 7 ga. formed steel channel frame to form
1 1/4 in. high guard rails. |
|
|
|
EZLogic: (See EZLogic Components Below) |
|
|
|
|
|
GUARD RAILS – Adjustable Universal Channel
Guard Rail (both sides), fixed channel (one side),
or angle (one side). |
|
|
|
PRICES
FOR COMPLETE CONVEYOR INCLUDE: |
|
|
|
|
•
1.9” Dia. x 9 Ga. Roller (Rollers on 4” or 6” Centers)
in a 3 1/2” x 7 Ga. Formed Channel on side opposite
chain guard and 4 3/4” x 7 Ga. Formed Channel on
chain guard side
• No. 40 Chain Roller-to-Roller
• Accumulating Zones with EZDriveTM System and
EZ-Logic® Accumulation System. EZLogic® Zone
Controller NEMA 1, 2, IP62. UL Approved.
• Infeed Wake-Up Eye |
|
• 27 VDC, 100 Watt Power
Supply for Zone
Controllers (Requires 120 VAC or 230 VAC),
Single Phase Input
• 1/3 HP Shaft Mounted Gearmotor In Each Zone.
230-3Ph 60 Hz. or 460-3Ph 60 Hz. (Specify Exact
Voltage).
• Totally Enclosed Chain Guard
• 35 FPM Constant Conveying Speed
• Less Floor Supports |
|
|
|
|
NOTE:
Pushbutton Programmer or Programming Kit
for PC NOT INCLUDED in listed price. See EZLogic
Components below for information and pricing. |
|
|
|
|
|
 |
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
| Base Price |
| 230 Volt |
460 Volt |
575
Volt |
1-5 Zones
Single Output |
6-10 Zones
Dual Output |
1-10 Zones
Single Output |
11-20 Zones
Single Output |
1-8 Zones
Dual Output |
9-16 Zones
Dual Output |
|
|
|
|
|
|
|
|
| Conveying
Surface |
12
1/4" |
14
1/4" |
16
1/4" |
18
1/4" |
20
1/4" |
22
1/4" |
24
1/4" |
28
1/4" |
30
1/4" |
34
1/4" |
36
1/4" |
Between
Rail
Width |
15"
| 17"
| 19"
| 21"
| 23"
| 25"
| 27"
| 31"
| 33"
| 37"
| 39"
|
Overall
Frame
Width |
18"
| 20"
| 22"
| 24"
| 26"
| 28"
| 30"
| 34"
| 36"
| 40"
| 42"
|
| Zone
Price |
|
|
|
|
|
|
|
|
|
|
|
4"
Roller Centers
Per Foot |
|
|
|
|
|
|
|
|
|
|
|
6"
Roller Centers
Per Foot |
|
|
|
|
|
|
|
|
|
|
|
|
|
ACCUMULATION ZONE LENGTHS |
4" Roller Centers |
6" Roller Centers |
32" through 120"
on 4" Increments |
30" through 120"
on 6" Increments |
|
|
|
|
|
|
|
 |
|
|
|
|
|
NOTE:
Total specification of product is required; product is recommended
for testing. Product footprint may affect drive capacity. |
|
|
|
|
|
|
| NOTE:
Section lengths and OAL change with zone lengths. |
|
|
|
|
|
|
PRICING
EXAMPLE:
15’ OAL x 18” OAW, 4” Roller Centers,
with (3) 60” Zones, 230 VOLT, Single
Output with (4) MSN-6 Supports for
32” elevation |
|
|
 |
|
|
|
| Base
(2,621) .............................. $2,621.00 |
|
| (3)
Zones x 3011.00 .................. $9,033.00 |
|
| 15
ft. x 218.60 ........................... $3,279.00 |
|
| (4)
MSN-6 Supports .................. $ 373.60 |
|
| Total
........................................ $15,306.60 |
|
|
|
| IMPORTANT
NOTES . . . |
• OTHER LENGTHS For lengths shorter than
5’-0”, price as 5’-0” OAL. For fractional lengths,
round up to nearest foot. Use per foot price of
width x OAL + zone price x total number of zones,
plus base price. |
• FLOOR SUPPORTS
Floor Supports are not included in base price.
There are two (2) stationary floor supports
required for the first bed section and one (1) support
required per bed section thereafter. |
| |
NOTE: OAL must be divisible by zone length.
Zone length must be divisible by roller centers. |
NOTE: Longer zones may require an additional
floor support depending on product load. |
• OTHER WIDTHS
For “IN-BETWEEN WIDTHS”, use next width plus
10%. For widths above 42” OAW and up to 63” OAW,
interpolate plus 10%. For widths above 63”
OAW,
contact us for lead time. All non-standard widths contact
us for lead time. |
|
|
|
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
|
|
|
|
|
|
|
|
| PRICES
FOR OPTIONAL EQUIPMENT |
|
|
|
|
|
|
|
|
| •FLOOR
SUPPORTS |
|
• EZDrive™ System |
|
Not
included in Base Price. Use Chart below for required
elevation. |
|
|
Variable
Frequency ... Add Per Zone ... |
$1,024.70 |
|
|
|
|
|
|
|
|
(*FOR
LONGER THAN 60” ZONES, ADD
“LONGER ZONE” PRICING LISTED BELOW.) |
|
| MS FLOOR SUPPORTS |
| Model No. |
Adjustment to Top of Roller |
Price Each. |
| MSN-1* |
10-3/4" to 12-1/2" |
|
| MSN-1.2* |
11-3/4" to 13-1/2" |
|
| MSN-1.4* |
12-3/4" to 14-1/2" |
|
| MSN-2* |
13-3/4" to 16-3/4" |
|
| MSN-3* |
16-11/16" to 19-11/16" |
|
| MSN-4 |
19-11/16" to 25-11/16" |
|
| MSN-5 |
23-11/16" to 29-11/16" |
|
| MSN-6 |
27-11/16" to 39-11/16" |
|
| MSN-7 |
37-11/16" to 49-11/16" |
|
| MSN-8 |
49-11/16" to 61-11/16" |
|
| MSN-9 |
61-11/16" to 73-11/16" |
|
| MSN-10 |
73-11/16" to 85-11/16" |
|
| MSN-11 |
83-11/16" to 95-11/16" |
|
| MSN-12 |
95-11/16" to 107-11/16" |
|
|
|
|
|
|
|
|
|
|
|
|
• EZLogic® System |
|
|
|
(See bottom of page) |
|
|
|
|
|
|
|
|
• GUARD RAILS |
|
|
|
Angle
Type “A”
1 1/2" x 1 1/2" x 12 Ga.
One Side . . . . . . . . . .Per Foot . . . . . . . . |
|
|
|
|
$4.10 |
|
|
|
Fixed
Channel Type
3 1/2” x 1 1/2” x 12 Ga. (Opposite Chain Guard) |
|
|
|
One
Side . . . . . . . . . .Per Foot . . . . . . . . |
$12.00 |
|
|
|
|
|
|
|
|
• DIFFUSE ZONE CONTROLLERS |
|
|
|
Add
Per Zone ......................................... |
$31.10 |
|
|
|
|
|
|
|
|
• GALVANIZING |
|
|
|
Contact
us. |
|
|
|
|
|
|
|
|
• LONGER ZONES-230/460 VOLT |
|
|
|
64"-90" |
|
|
|
|
|
|
|
|
NOTE: MSN-7 to MSN-12: Knee Braces included in price. |
|
|
|
|
|
|
3’-0”
Connector Cable..... Add Per Zone.... |
$325.60 |
|
Extra
Knee Braces.................... Per Pair................. |
$31.80 |
|
|
|
|
|
100”
- 120”
6’-0” Connector Cable..... Add Per Zone.... |
|
|
|
|
|
|
|
| • CONSTANT AND VARIABLE SPEEDS |
|
|
|
|
|
$325.60 |
|
|
|
|
|
|
Constant
Speed—35 or 58 FPM. For other speeds,
contact us for lead time. |
|
|
|
|
|
|
|
• LONGER ZONES - 575 VOLT |
|
|
|
30”
- 60”.......... Add Per Zone.................... |
$643.20 |
|
|
|
|
|
| • DRIVE COMPONENT DEDUCTS |
|
|
|
|
64”
- 90” |
|
|
Less
Gearmotor Only (1/3 HP-230/460V-3 Ph.-60 Hz.) |
|
|
3’-0”
Connector Cable...Add Per Zone....... |
$968.30 |
|
(Per Zone) .......Deduct
........................ |
$419.30 |
|
|
100”
- 120”
6’-0” Connector Cable...Add Per Zone....... |
|
|
|
|
|
|
$968.30 |
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
| • CEILING HANGERS |
|
Ceiling
Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated
fully threaded rods ...................................................................... |
|
 |
$156.70 |
Ceiling
Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized
fully threaded rods ....................................................................... |
|
| $187.20 |
Ceiling
Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated
fully
threaded rods................................................................................ |
|
| $231.60 |
| Ceiling
Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized
fully threaded rods................................................................................. |
|
| $381.20 |
| Ceiling
Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated
fully threaded rods................................................................................. |
|
|
|
|
$384.40 |
|
Ceiling
Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized
fully threaded rods.................................................................................. |
|
|
$444.50 |
|
Ceiling Hanger
Brackets, Less Rods Only .................................... |
$98.70 |
|
Extra Length Rods: |
|
|
(2) 8’-0”
long x 5/8” dia. unplated fully threaded rods .................. |
$57.40 |
|
(2) 8’-0”
long x 5/8” dia. galvanized fully threaded rods ............... |
$88.40 |
|
(2) 10’-0”
long x 5/8” dia. unplated fully threaded rods ................ |
$132.70 |
|
(2) 10’-0”
long x 5/8” dia. galvanized fully threaded rods ............. |
$282.30 |
|
(2) 12’-0”
long x 5/8” dia. unplated fully threaded rods ................ |
$285.80 |
|
(2) 12’-0”
long x 5/8” dia. galvanized fully threaded rods ............. |
$346.00 |
|
Hex Coupling Nuts
for Rods ......................................................... |
$5.20 |
|
Above
noted delivery times determined by delivery time of model ordered. |
|
|
|
| • POLY-TIER SUPPORTS |
 |
|
PRICES
FOR COMPLETE
SUPPORT INCLUDE: |
|
|
|
IMPORTANT
NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only. |
|
•
Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
conveyor)
• "U" Brackets
• Single Width Conveyor Only |
|
|
|
|
|
|
|
|
|
|
|
|
CAPACITY
DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs |
|
|
|
|
|
|
|
|
|
|
|
|
| (2) TIER POLY-TIER SUPPORTS |
36" |
|
42" |
|
48" |
|
54" |
|
60" |
|
66" |
|
72" |
|
78" |
|
84" |
|
90" |
|
96" |
|
102" |
|
108" |
|
114" |
|
120" |
|
|
|
| (3) TIER POLY-TIER SUPPORTS |
36" |
|
42" |
|
48" |
|
54" |
|
60" |
|
66" |
|
72" |
|
78" |
|
84" |
|
90" |
|
96" |
|
102" |
|
108" |
|
114" |
|
120" |
|
|
|
|
|
|
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
| ZONE
CONTROLLERS |
|
|
|
|
|
 |
|
|
|
|
|
|
Retro-Reflective
Type Zone Controller |
|
|
|
Zone
controller including mounting base and unitized retro-reflective transducer.
032.501 .......................................................................................................................... |
|
|
$369.80 |
|
|
|
|
|
Diffuse Type
Zone Controller |
|
|
|
Zone
controller including mounting base and unitized diffuse transducer with
adjustable
sensitivity (through programming). |
|
|
032.502
.................................. Add-On ............................................Per
Zone ...................... |
|
|
032.502
.................................. Replacement ........................................................................... |
|
|
|
|
|
|
Enhanced Retro-Reflective
Zone Controller |
|
|
|
Same
as standard, plus used for IOP communication, and addressable remote access. |
|
|
032.505
.................................. Add-On ............................................Per
Zone ................... |
|
|
032.505
.................................. Replacement ........................................................................ |
|
|
|
|
|
|
Enhanced
Diffuse Zone Controller |
|
|
Same
as standard, plus used for IOP communication, and addressable remote access. |
|
|
032.506
.................................. Add-On ............................................Per
Zone ................... |
$246.90 |
|
032.506
.................................. Replacement ........................................................................ |
$450.60 |
|
|
|
|
|
Remote
Zone Controller |
|
|
Zone
controller including mounting base. Connectorized for attaching any remote
transducer. |
|
|
032.504
.................................. Replacement ........................................................................ |
$398.60 |
|
Enhanced Remote
Zone Controller |
|
|
|
Enhanced
zone controller including mounting base. Connectorized for attaching any
remote
transducer. Same as standard, plus used for IOP communication, and addressable
remote
access. |
|
|
032.507
.................................. Replacement ........................................................................ |
$556.90 |
|
|
|
|
|
|
|
|
|
| TRANSDUCERS
(SENSORS) |
|
 |
|
|
|
|
|
| Remote
Diffuse Transducer (Narrow Beam) |
|
|
Has
narrow beam for use with close roller centers. Attaches to any remote zone
controller and allows transducer to be mounted separate from controller. |
|
|
| 032.513
.................................. Replacement .................................. |
$235.60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
| IOP |
|
|
|
|
|
|
|
|
|
| IOP |
|
 |
|
Provides
27VDC, 100 watt power for EZLogic“ accumulation
system. Requires 120 VAC or 230 VAC single phase input.
Operates up to 50 zones (25 zones each side of IOP).– contains
slots for 4 input/ output boards. Requires enhanced zone controllers
to communicate with input/output boards. |
|
|
| 032.582
.................................. Each ....................... |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| IOP
"T" Cable |
|
|
 |
|
|
Required
to deliver power and IOP communication from IOP to
zone controllers. Max. of 25 zones per each branch of T. |
|
|
|
|
| Standard
Push-On 032.559 .....Each .......................... |
$116.50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| I/O
Board |
|
|
 |
|
|
|
Plugs
into slot in IOP to provide two input/output connections.
Requires enhanced controller to receive signal. |
|
|
|
|
|
| 032.583
.................................. Each ............................... |
$154.02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CONFIGURATION/DIAGNOSTIC
COMPONENTS |
|
|
|
 |
| Push
Button Programmer |
|
Plugs
into auxiliary port of any controller to configure certain features of
controller. Required for customization of factory default settings. |
|
| 032.535
.................................. Each ............................... |
$623.70 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
| Programming Kit for PC and PC Adaptor |
|
|
|
|
Used
to connect PC USB port to auxiliary port of any controller. Includes GenesisTM
configuration software. Used to configure all
features of controller. Required for customization of factory default settings. |
|
|
|
|
| K-01554
.................................. Each ............................... |
$568.20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUXILIARY
COMPONENTS |
|
|
|
|
|
|
|
|
|
| Auxiliary
I/O Module |
 |
|
|
Plugs
into auxiliary port of any controller - used to
provide photo eye output or to accept a voltage type
input. |
| 032.532
.................................................... |
$128.10 |
|
|
| Auxiliary
Input Cable |
|
|
|
|
|
|
|
Attaches
to any zone controller. Used for zone stop input, wakeup eye input,
or slug input. Available in 3 and 10 ft. lengths. |
|
|
|
|
 |
|
|
|
|
|
|
|
|
| 3
ft. ............................032.563 ....................................Each
.................. |
$54.40 |
|
|
| 10
ft. ..........................032.564 ....................................Each
.................. |
$57.18 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone
Actuation Module “ZAM” (Alternate Drive)
Provides NPN, PNP, or dry contact output from zone controller. |
|
|
 |
| 032.531
......................................................Each................................ |
$126.40 |
|
|
|
|
|
|
|
|
|
Retro-Reflective
Wake-up Eye
Plugs into auxiliary port of any controller to send wake-up signal. |
|
| 032.591
......................................................Each................................ |
$218.30 |
|
|
|
|
|
|
|
|
Diffuse
Wake-up Eye
Plugs into auxiliary port of any controller to send wake-up signal. |
|
|
| 032.592
......................................................Each................................ |
$252.60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Retro-Reflectors |
|
|
|
|
|
|
| 2.18”
Dia. 032.218 .....................................Each ............................... |
$3.40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Connector
Covers |
|
|
|
|
|
|
| Upstream
Connector Cover 032.010 .............Each ............................... |
$7.50 |
|
|
|
|
| Downstream
Connector Cover 032.011..........Each ............................... |
$7.50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click a Price of the item you wish to purchase. |
|
|
| CABLE
COMPONENTS |
|
|
|
|
|
|
|
|
|
|
|
| Power
Isolation Cable |
|
|
|
|
|
|
 |
|
Required
to isolate DC power when joining conveyors w/ separate IOPs
utilizing no more than one set of I/O boards. |
|
|
| Standard
Push-On ................... 032.562 ....................Each ............. |
$70.70 |
|
|
|
|
|
|
|
|
|
| IOP
Isolation Cable |
|
|
Required
to isolate DC power and input/output signals when joining two
conveyors with separate IOPs, both utilizing I/O boards. |
|
|
| Standard
Push-On ................... 032.570 ....................Each ............. |
$70.70 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Extension
Cable (Zone to Zone Communication) |
|
|
|
|
| Available
in 3 and 10 ft. lengths. Used to extend zone controller cable when necessary. |
|
|
|
|
| Standard
Push-On 3 ft.................... 032.560 ....................Each ......... |
$92.50 |
|
|
|
|
| Standard
Push-On 10 ft.................... 032.561 ....................Each ........ |
$120.20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Nano
Extension Cable |
|
|
|
|
| Used
to extend auxiliary devices or remote transducer cable. Available in the
following lengths: |
|
|
| 1
ft ........................... 032.565 ...........................................Replacement
................. |
$56.80 |
|
|
|
| 2
ft ........................... 032.566 ...........................................Replacement
................. |
$60.40 |
|
|
|
| 3
ft ........................... 032.567 ...........................................Replacement
................. |
$63.40 |
|
|
|
| 6
ft ........................... 032.568 ...........................................Replacement
................. |
$72.70 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Power
Splitter |
|
|
 |
| Used
to connect two conveyors located side by side to one IOP. Requires 2 power
supply T cables. Maximum total of 50 zones. |
|
|
| 032.569
...............................Each ........................ |
$77.30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SPECIAL
USE COMPONENTS |
|
|
|
|
|
|
|
|
| Diffuse
Type Zone Controller |
|
|
 |
|
Zone
controller including mounting base and unitized diffuse transducer with
adjustable sensitivity (through programming). 24 in. cable. |
|
|
|
| 032.503
.......................................Each ................................ |
$435.80 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Remote
Retro-Reflective Transducer |
|
|
 |
|
|
Attaches
to any remote zone controller and allows transducer to be mounted
separate from controller. |
|
|
|
|
| 032.511
.............................................Each .............................. |
$143.30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Remote
Diffuse Transducer |
|
|
 |
|
|
|
Attaches
to any remote zone controller and allows transducer to be mounted
separate from controller. |
|
|
|
|
|
| 032.512
............................................Each .............................. |
$189.60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Remote
Retro-Reflective Transducer (Dual with T Cable) |
|
|
|
|
|
|
For
use in dual head applications. Attaches to any remote zone controller
and allows addition of second remote transducer. |
|
|
|
|
|
|
|
 |
|
| 032.514
..........................................Replacement .................. |
$332.90 |
|
|
|
|
|
|
| Remote
Diffuse Transducer (Dual with T Cable) |
|
|
For
use in dual head applications. Attaches to any remote zone
controller and allows addition of second remote transducer. |
|
|
| 032.515
...................................................Replacement .............. |
$379.00 |
|
|
|
|
|
|
| Remote
Diffuse Transducer (Narrow Beam, Dual with T Cable) |
|
|
For
use in dual head applications. Has narrow beam for use with close roller
centers. Attaches to any remote zone controller and allows addition of second
remote transducer. |
|
|
|
|
|
|
| 032.516
...................................................Replacement .............. |
$435.80 |
|
|
|
|
|
|
|
Heavy Duty Accumulating Conveyor,
Chain Driven Live Roller Conveyors, Conveyor, Live Roller Conveyors,
Powered Live Roller, Zero Pressure, Conveyors, and Roller Conveyors from
your source for material handling
equipment. |
Back
to Product Category |
 |
|
