Belt Conveyors, Portable Parts Conveyor, Incline Conveyor, Conveyors

ENGINEERED STEEL PRODUCTS

Priced Full Line Products Catalog

20 Technology Way • West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401) 421-5679

Back to Product Category

MODEL PC
PORTABLE PARTS CONVEYOR

The Model PC can be used as a portable or permanent parts conveyor. Side guards and cleated belt easily catch small stampings, plastic parts, etc., and carry them to hoppers or drums. Flapper guard prevents parts from falling through conveyor.

8 Belt Widths
Tough Cleated Belt
Portable or Permanent
Overhead Drive
Formed Edge Guard Rails


STANDARD SPECIFICATIONS

BELT–3- ply black Nitrile with 1-1/2 in. high molded cleats on 12 in. centers. Clipper unibar lacing.		DRIVE PULLEY–4 in. dia. With 1 in. dia. Shaft at bearings, machine crowned and fully lagged.
BED–6-5/8 in. deep x 12 ga powder painted formed steel slider bed. 3-1/2 in. high vertical sides with rolled edge. Standard sections are 4 ft., 6 ft., 8 ft., 10 ft., and 12 ft. long. Longer bed sections are bolted together with splice plates and joint support angles.		BELT RETURN–4 in. dia. with 1 in. dia. shaft at bearings, machine crowned.
		TAKE-UP–Take-ups provided at tail pulley. Provides 4 in. of belt take-up.
		BEARINGS–Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys.
PORTABLE BASE SUPPORT–Tubular steel support mounted on 4 in. dia. steel wheels. Adjustable to control conveyor height at top and bottom. Adjustment height can be locked in place with lever. NOTE: Not available on units longer than 13 ft.
		SPEED REDUCTION–Sealed worm gear “C” face speed reducer. No. 50 roller chain to drive pulley.
		MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed ”C” face.
OVERHEAD END DRIVE–Motor reducer unit mounted 9-1/2 in. above belt (chain guard RH side).		BELT SPEED–Constant 65 FPM.
		CAPACITY–300 lbs. total distributed load at 65 FPM.


FEEDER SHOWN WITH STANDARD PC TYPE GUARD RAIL, GRAVITY BRACKET WITH POP-OUT ROLLER AND OPTIONAL MS TYPE FLOOR SUPPORTS


OPTIONAL EQUIPMENT

BELT–1/2 in. x 1 in. galvanized flat wire mesh belt with 1-1/4 in. high steel angle cleats, spaced every 12 in. Galvanized low carbon steel or stainless steel. 1 in. x 1 in. or 1/2 in. x 1/2 in. mesh available.		HIGHER SIDE GUARDS–6 in., 9 in., or 12 in. high vertical sides in place of standard 3-1/2 in. high. NOTE: 12 in. high sides require higher than standard overhead or underside drive.
BELT SPEED–Other constant and variable speeds. V-belt drive supplied under 17 FPM. NOTE: Capacity affected with speed change.		LOWER POWERED FEEDER–Chain type driven from tail pulley of conveyor. Black friction surface belt. Includes MS-6 support. NOTE: conveyor tail pulley is used for belt take-up. When belt tension is adjusted, feeder will have to be moved along with the take-up. NOTE: Capacity affected with this option.
OVERHEAD END DRIVE–Higher than standard clearance above belt, specify.
UNDERSIDE END DRIVE–Motor reducer unit mounted underneath bed. Extends down 11 in. from bottom of bed.
		FLOOR SUPPORTS–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-3 support.
PULLEYS–6 in. tail with 1-3/16 in. dia. Shaft at bearings or 8 in. drive with 1-3/16 in. dia. Shaft at bearings.
V-BELT DRIVE–V-belt supplied between motor and reducer. Minimum overall drive width 14 in.
O-RING DRIVE CHAIN–With sealed in lubricant (Recommended for applications that do not permit regular lubrication).		MOTORS–Energy efficient, single phase, other characteristics. 2 HP maximum.
		ELECTRICAL CONTROLS–One direction manual start switch. Non-reversing magnetic starters. Push button stations. AC variable frequency drive.


PRICES FOR COMPLETE CONVEYOR INCLUDE:

3-Ply Black Nitrile Belt with 1-1/2" High Cleats on 12" Center.		1/2 HP-"C" Face Totally Enclosed Motor (Specify Exact Voltage)
6-5/8" Deep x 12 Ga. Slider Bed with 3-1/2" Guard Rails.		Totally Enclosed Chain Guard
6-5/8" Deep x 12 Ga. Slider Bed with 3-1/2" Guard Rails.		65 FPM Constant Belt Speed
Overhead End Drive		Less Electrical Controls
Portable Base Support
"C" Face Speed Reducer-Sealed Worm Gear


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

SIZE TO ORDER Overall Length "A"	Bed Length "L"	3-Ply Black Nitrile Belt Width
		4"	6"	8"	10"	12"	16"	18"	24"
		12 Ga. Steel Slider Bed Width
		8"	10"	12"	14"	16"	20"	22"	28"
		Price	Price	Price	Price	Price	Price	Price	Price
5'	4'	$3,458	$3,725	$3,992	$4,259	$4,527	$5,059	$5,327	$6,128
7'	6'	$3,654	$3,967	$4,280	$4,593	$4,906	$5,532	$5,845	$6,784
9'	8'	$3,849	$4,209	$4,569	$4,927	$5,287	$6,004	$6,364	$7,441
11'	10'	$4,046	$4,451	$4,856	$5,261	$5,667	$6,477	$6,882	$8,097
13'	12'	$4,242	$4,693	$5,145	$5,596	$6,047	$6,949	$7,400	$8,753
Per Foot Price		$97.70	$121.00	$144.30	$166.50	$236.40	$236.40	$259.70	$328.60

Lengths other than those listed are (4) week delivery.


*IMPORTANT NOTES...*
OTHER WIDTHS		PORTABLE BASE
	For "IN-BETWEEN WIDTHS", contact us.		Portable Base Not Supplied on Conveyor Longer than 13’ or with Underside Drive. Deduct Portable Base and add MS-Type Floor Supports.
NON-STANDARD WIDTHS
	Contact us for lead time.

PRICES FOR OPTIONAL EQUIPMENT

OPTIONAL BELTS

HIGHER SIDES

1/2" x 1" Galvanized Flat Wire Mesh with 1-1/4" High
Steel Cleats on 12" Centers .......................................

Sides Higher than 3-1/2": Add-on per foot both sides

.....................................6" .............................. $3.20

................................................No Additional Charge.

.....................................9" ...............................$8.00

.....................................12" ............................ $12.50

OPTIONAL DRIVES

Drive Type	BED WIDTHS
Drive Type	8" to 20"	22" to 28"
Overhead C-Face	N/C	N/C
Overhead V-Belt	$246.50	$246.50
Underside C-Face	$552.50	$704.30
Underside V-Belt	$798.90	$950.40

HOPPER

............................... ..................................... $677.10

CONSTANT AND VARIABLE SPEEDS

Constant C-Face-Within 17-135 FPM .....No Charge

Constant V-Belt-Minimum of 4 FPM ..........................

.......................................Use V-Belt Drive Add-On

Constant Speeds Below Those Listed Above ..............

..................................................................Contact Us

#50 O-Ring Drive Chain ........... Add .............$284.40

Variable Speed ................See Electrical Controls and

* NOTE: Not Available on 5' OAL Units

Drive Section below

FLOOR SUPPORTS

Deduct Portable Base and Add Per Support. Specify
top of belt elevation.

DRIVE COMPONENT

Less Motor Drive, Motor Mount and Guards, but with

"MS" SUPPORT
Model No.	Hts. Adj. To Top of Belt	Price Each
MSL-1	8-3/4" to 9-3/4"	$58.40
MSL-2	9-3/4" to 11-1/2"	$58.40
MSL-3	11-1/2" to 14-1/8"	$58.40
MS-1	13-3/4" to 15-1/2"	$58.40
MS-1.2	14-3/4" to 16-1/2"	$58.40
MS-1.4	15-3/4" to 17-1/2"	$58.40
MS-2	16-3/4" to 19-3/4"	$60.40
MS-3	19-3/8" to 22-3/8"	$66.40
MS-4	22-3/8" to 28-3/8"	$76.40
MS-5	26-3/8" to 32-3/8"	$79.80
MS-6	30-3/8" to 42-3/8"	$88.10
MS-7	40-3/8" to 52-3/8"	$130.20
MS-8	52-3/8" to 64-3/8"	$148.50
MS-9	64-3/8" to 76-3/8"	$162.80
MS-10	76-3/8" to 88-3/8"	$185.60
MS-11	86-3/8" to 98-3/8"	$205.20
MS-12	98-3/8" to 110-3/8"	$214.60

Shaft Extension ..............Deduct ..................

$694.20

Less Motor Only (1/2 HP-208/230/460/575V-

Ph.60 Hz.).....................Deduct ................... $258.30

* Less Reducer .............Deduct ..................

$307.40

* Less V-Belt Guard, Chain Guard, sheaves and sprockets
when V-Belt drive is supplied. Less chain guard and
sprockets when C-Face drive is supplied.

ELECTRICAL CONTROLS

(See below)

GALVANIZING

Less Portable Base ..............Deduct ...........

$438.90

Knee Braces .................Add per pair ..........

$30.00

NOTE: Specify Infeed and Discharge Elevation.

NOTE: MS-3 to MS-12: Knee Braces included in price.


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

MOTORS

Extra Motor Price for OTHER THAN: 1/2 HP–208/230/460/575 V–3 Ph.–60 Hz.–Totally Enclosed. Speed affects
horsepower requirements.

H.P. REQ.	TOTALLY ENCLOSED		ENERGY EFFICIENT
H.P. REQ.	200/208/230/ 460/575V 3 Ph.-60 Hz.	115/230V 1 Ph.-60 Hz.	230/460V 1 Ph.-60 Hz.	575V 3 Ph.-60 Hz.
1/2	N/C	$39.30	$400.90	$400.90
1	N/A	$143.20	$498.10	$498.10
2	N/A	$1,206.80	$972.10	$972.10

LARGER DRIVE OR TAIL PULLEY

POWERED FEEDER

Bed Widths	8" Dia. Drive Pulley in Lieu of 4" Dia.	6" Dia. Tail Pulley in Lieu of 4" Dia.
8" to 12"	$620.00	$359.60
14" to 20"	$733.80	$359.60
22"	$817.80	$359.60
28"	$926.10	$359.60

Prices for Powered Feeder Include:

Black Ultimate 140 BOS Belt, Bed, Drive & Tail Pulleys

NOTE: Adjustable Floor Support Not Included in Base Price

NOTE: Overall length of 29-1/2" requires 1 support

Overall length of 44-1/2" or more requires 2
supports

NOTE: NO DEDUCT for Feeders less than minimum
lengths. Shorter lengths COULD CAUSE IMPROPER
BELT TRACKING

CHAIN DRIVEN TYPE

BELT WIDTHS	4"	6"	8"	10"	12"	16"	18"	24"
Min. Length Overall	29-1/2"	29-1/2"	29-1/2"	29-1/2"	29-1/2"	44-1/2"	44-1/2"	63-1/2"
Price	$1,349	$1,433	$1,517	$1,600	$1,685	$2,042	$2,131	$2,719
Price Per Foot	$84.20	$91.90	$100.20	$108.10	$116.30	$133.00	$133.90	$168.30

#50 O-Ring Chain on Feeder Slave Connection .........Add .............. $203.50


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

ELECTRICAL CONTROLS AND DRIVE SECTION

MANUAL START SWITCH or
SAFETY DISCONNECT

LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER

#032.1014.........................................

$213.01

#033.2032 & #033.2072..................$555.67
Nema 4

"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)

LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER

#033.2033& #033.2072...................$332.11
Nema 4

REVERSING DRUM SWITCH

#032.103..........................................

$854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase

PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range

FOOT SWITCH WITH GUARD

#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range

#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.

PHOTO EYE, ON-OFF TYPE

#EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC

POWER CORD AND PLUG (20')

POWER CORD WITH PLUG ONLY 20' LONG
Model No.	Voltage	HP Rating	Prices
EA-039-1A	115/1	1/2-3/4	$106.67
EA-039-2A	115/1	1	$106.67
EA-039-3A	115/1	1 1/2	$155.18
EA-039-4A	230/1	1/2-1	$106.67
EA-039-5A	230/1	1 1/2-2	$109.67
EA-039-6A	208-230/3	1/2-2	$178.60
EA-039-7A	460/3	1/2-2	$178.60

POWER CORD WITH PLUG 20' LONG WITH MANUA
Model No.	Voltage	HP Rating	Prices
EA-039-1B	115/1	1/2-3/4	$173.16
EA-039-2B	115/1	1	$330.67
EA-039-3B	115/1	1 1/2	$377.96
EA-039-4B	230/1	1/2-1	$293.04
EA-039-5B	230/1	1 1/2-2	$330.67
EA-039-6B	208-230/3	1/2-2	$362.97
EA-039-7B	460/3	1/2-2	$362.97

MOUNTING BRACKETS FOR PHOTO
EYE #033.2122

B-05165...........................................$118.10

AIR PRESSURE SWITCH

#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH

#032.285 with 032.2851 Turnbuckle
...........................................................$696.08
Nema 4

"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE

#032.281...one side.................$7.44 per / ft.
both sides..............$15.87per / ft.

EMERGENCY PUSH BUTTON

#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE

#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48

NOTE: PRICING LISTED NOT MOUNTED
OR WIRED

"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC

#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

CONTROLLER PRICES

AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size	115 Volt		208/230 Volt
1/2	VSC-12-10		VSC-12-12
Price	$1,491.84		$1,189.37
1	VSC-12-11		VSC-12-13
Price	$1,724.27		$1,391.05
2	N/A		VSC-12-14
Price	~		$1,794.20
THREE PHASE CONTROLLER INPUT
Motor Size	208/230 Volt	460 Volt	575 Volt
1/2	VSC-01-15	VSC-01-18	VSC-12-29
Price	$1,564.99	$1,656.34	$2,155.73
1	VSC-01-16	VSC-01-19	VSC-12-29
Price	$1,579.75	$1,794.20	$2,155.73
2	VSC-01-17	VSC01--20	VSC-12-30
Price	$1,978.69	$2,070.37	$2,663.45

REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS

HP	Part No.	Price
1/2	032.351 230/460	$618.71
1	032.353 230/460	$705.52
2	032.355 230/460	$797.31
1/2	032.3512 575	$1,449.11
1	032.3532 575	$1,611.17
2	032.3552 575	$1,897.10

IMPORTANT NOTES...

• All above motors are 230 / 460 / 575 Volt, 3 Phase.
• All above V/S Drive Kits include NEMA 1 / IP30
Junction Box, Controller and Motor.
• Good for cycle rates of up to 15 cycles per minute, at
1/2 second ramp time, with a maximum speed of 250
FPM.
• Drawing No. DG-001146.

OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)

$675.20

• When AC Variable Speed Controller is used with a
Brake Motor, A Brake Relay Kit (EA-068A) is
required. Add an additional $542.68 for this option.)

Brake Relay Kit (EA-068A)..............................

$542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE

Part No.	Description	Price
EA-VSC-01-CB	2 HP Electronic Clutch-Brake Kit	$5,058.00

OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)

$675.20

KIT INCLUDES

Part No.	Description
VSC-01-20	AC Variable Speed Controller, 460 Volt, 3 Phase
032.345	2 HP 460 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

IMPORTANT NOTES

• Good for cycle rates of up to 60 cycles per minute.
• 1/10 second Accel and Decel time, with 350 FPM
Maximum Speed.
• 230 or 460 Volt Only, Other Voltages, Contact us.
• Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
• Price Includes 5AC Reducer and #60 Chain and
Sprockets

Part No.	Description
VSC-01-17	AC Variable Speed Controller, 230 Volt, 3 Phase
032.345	2 HP 230 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)

An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.

THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	MOTOR DUTY	NON-REVERSING					REVERSING
H.P.	MOTOR DUTY	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE
1/2	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B25	EN-46B16	EN-57B10	$1516.60	ER-20B40	ER-23B25	ER-46B16	ER-57B10	$2,023.30
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B16	EN-46B10				ER-23B16	ER-46B10
1	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B40	EN-46B25	EN-57B16		ER-20B40	ER-23B40	ER-46B25	ER-57B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
1-1/2	GEARMOTORS	EN-20C10	EN-23B63	EN-46B40	EN-57B25		ER-20C10	ER-23B63	ER-46B40	ER-57B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
2	STANDARD EASY CLEAN ENERG. EFF.	EN-20C10	EN-23C10	EN-46B40	EN-57B40		ER-20C10	ER-23C10	ER-46B40	ER-57B40
			EN-23C10	EN-46B40				ER-23C10	ER-46B40
			EN-23B63	EN-46B40				ER-23B63	ER-46B40

SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	NON-REVERSING		REVERSING		NON-REVERSING		REVERSING
	115 VOLT	PRICE	115 VOLT	PRICE	230 VOLT	PRICE	230 VOLT	PRICE
1/2	EN-1SC10	$1,182.40	ER-1SC10	$2,023.30	EN-2SB63	$1,435.60	ER-2SB63	$2,023.30
1	EN-1SC16		ER-1SC16		EN-2SC10		ER-2SC10
1-1/2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10
2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10


• Manual Start-Stop Switch Kit			• Start-Stop Push Button Kit, Remote Mounted
	EA-000001 ......................................	$242.09		EA-000002.......................................	$242.09
	Includes: 032.1014 Manual Start Switch, Nema 1, B-21467 Mounting Bracket with Mounting Hardware			Includes: 033.1955 Push Button Station, One Direction, Nema1, B-21467 Mounting Bracket with Mounting Hardware

• Forward-Reverse-Stop Push Button Kit, Remote Mounted

			• Up-Down-Stop Push Button Kit, Remote Mounted
	EA-000003.......................................	$440.67	• Up-Down-Stop Push Button Kit, Remote Mounted
	Includes: 033.1965 Push Button Station, Reversing, Nema1, B-21467 Mounting Bracket with Mounting Hardware			EA-000004.......................................	$440.67
				Includes: 033.1975 Up Down Stop Push Button Station, Reversing, Nema 1, B-21467 Mounting Bracket with Mounting Hardware


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station				• “Start-Stop”Push-button Station
033.1955			$211.23		033.195.................................................	$142.50
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Fwd-Rev-Stop” Push-button Station				• “Fwd-Rev-Stop”Push Button Station
033.1965			$397.05		033.196..................................................	$490.95
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Up-Down-Stop” Push-button Station				OPTIONAL STARTER CONTROLS
033.1975			$397.05	OPTIONAL STARTER CONTROLS
033.1975			$397.05	• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1				• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1					EA-011 ............................................ Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), and a Control Circuit Transformer (As Required), & Pushbutton Station (033.195).	$3,210.68
						$3,210.68

IMPORTANT NOTES
• Control Circuit Transformer Included for 115 Volt Control Voltage. • Above starters are in Nema 3, 4 and 12 Enclosures. • The starters included Safety Disconnect, Overload Relay, and Aux. Contacts as required. • IF AN ORDER IS SUPPLIED LESS MOTOR, AND IS SUPPLYING ANY ELECTRICAL CONTROLS, THEN MOTOR HP, VOLTAGE, PHASE, AND FULL LOAD CURRENT MUST BE STATED ON THE ORDER. • PRICING LISTED IS NOT MOUNTED OR WIRED.

				• Auto Restart Control, 1 Phase, Non-Reversing
					EA-012 (115 Volt) ........................... EA-017 (230 Volt) ........................... Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), Pushbutton Station (033.195), and (230 V. Only) a Control Circuit Transformer (As Required). Note: Above Price does NOT include Photo Eye Mounting Bracket.	$3,253.63
						$3,391.27

• Add on	$192.70	for the above Push Buttons
to be Mounted.
• Add on	$995.10	for the above Starters and
Push Button Stations to be Mounted and Wired. Supply 20'0" of cable for push button only.

				• Mounting Brackets for photo eye
				• Mounting Brackets for photo eye
					#033.2122 B-05165 ..............................................
						$118.10

CONVEYOR WEIGHT TABLE

SIZE TO ORDER Overall Length "A"	Belt Width	4"	6"	8"	10"	12"	16"	18"	24"
SIZE TO ORDER Overall Length "A"	Bed Width	8"	10"	12"	14"	16"	20"	22"	28"
5'	Weights (Lbs.)	348	416	420	473	477	530	583	635
7'		379	447	451	504	508	563	620	675
9'		410	478	482	535	539	596	657	714
11'		441	509	513	566	570	629	694	753
13'		472	540	544	597	601	662	731	792

All weights are conveyor weights only.

Accessories, crating, etc., are not included.

ADJUSTMENT CHART FOR 5' TO 13' LONG UNITS

Overall Length "A"	Bed Length "L"	Base Length	Minimum Tall		Minimum Tall		Maximum Tall		Maximum Tall		*"E"
			Minimum Drive		Maximum Drive		Minimum Drive		Maximum Drive
			"C"	"H"	"C"	"H"	"C"	"H"	"C"	"H"
5'	4'	22"	11"	41-1/2"	10"	56"	25-1/2"	37-1/2"	26"	54-1/2"	11"
7'	6'	34"		51-1/2"		76-1/2"	44-1/2"	44-1/2"	45"	73-1/2"
9'	8'	46"		64-1/2"		97-1/2"	57-1/2"	57-1/2"	48"	95-1/2"
11'	10'	58"		74-1/2"		118"	67-1/2"	67-1/2"	55-1/2"	116"
13'	12'	58"		86-1/2"		139"	67-1/2"	67-1/2"	55-1/2"	128"	35"

*APPLIES TO PORTABLE BASE ONLY

Belt Conveyors, Cleated Belt, Conveyor, Conveyor Belt, Portable Parts Conveyor, Incline Conveyor, Low Profile Conveyor, Parts
Conveyor, Portable Belt Conveyors, Conveyors, and Slider Bed from your source for material handling equipment.

Back to Product Category

Home - Order - Search - Quote - Contact Us - About Us - My Account - Shopping Cart

MODEL PC

PORTABLE PARTS CONVEYOR

Belt Conveyors, Cleated Belt, Conveyor, Conveyor Belt, Portable Parts Conveyor, Incline Conveyor, Low Profile Conveyor, Parts Conveyor, Portable Belt Conveyors, Conveyors, and Slider Bed from your source for material handling equipment.

Belt Conveyors, Cleated Belt, Conveyor, Conveyor Belt, Portable Parts Conveyor, Incline Conveyor, Low Profile Conveyor, Parts
Conveyor, Portable Belt Conveyors, Conveyors, and Slider Bed from your source for material handling equipment.