CONTEMPORARY TABLE DESIGN - 1044


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

			New contemporary table design for in-ground or standard surface mount.


			Specifications: Assembly required Size: 36" x 36" x 29" Unit Weight:* 135 lbs. Material: Aluminum, Galvanized Steel, Recycled Plastic Special Features: Surface mount

			Model: 1044 Price: $706.15


	Colors for Panels

Colors for Frame

TECHNICAL INFORMATION - POWDURA® Epoxy Powder Coating

PRODUCT DESCRIPTION
EAS6-00025
ZINC RICH PRIMER
POWDURA® Epoxy Powder Coating is recommended for a broad range of interior functional and
decorative applications.

APPLICATION
Cure Schedule: 10 min @ 205°C (401°F)
Film Thickness Range: 1.5-1.8 mils

ATTRIBUTES
Specific Gravity: 2.83 +/-0.05
Coverage at 1.0 mil: 67.8 sq.ft/lb
60 Gloss: Visual
Adhesion: No Failure with 1/16in. squares(5B) (ASTM D-3359)
Flexibility: Pass 1/8" Mandrel Bend (ASTM D-522)
Pencil Hardness: H-2H (ASTM D-3363)
Impact Resistance(dir/rev): 160/160 (ASTM D-2794)

Other Notes
SaltSpray Performance: When top coated with TGIC polyesters,urethanes and fluoroploymers, testing showed 4-5 mm
undercut at 5000 hours on Bonderite 1000

Storage:
POWDURA® Powder Coatings should be kept in a dry and cool area at temperatures below 80°F (26.7° C). Shelf
life is approximately 12 months.
When not in use, store powder in sealed containers: fine powders are hygroscopic.

Substrate Preparation
General: Substrate should be free of grease, oil, dirt, fingerprints, drawing compounds, any contamination, and surface
preparation treatments to ensure optimum adhesion and coating performance properties. The use of a chemical
conversion coating prior to the application of a powder coating is strongly recommended. Consult Metal Preparation
Brochure CC-T1 for additional details.

Aluminum: A minimum of a 5-stage chrome phosphate metal treatment, or equivalent, is required for good adhesion
and optimum coating performance properties.

Testing:
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, the
customer should test the complete system for adhesion and compatibility prior to full-scale application. The properties
listed are typical and should not be construed as the actual specification.

Product Limitations:
Contact your Sherwin-Williams Representative where use of this product at higher than recommended film thickness
may be required.

APPLICATION:
Powder coatings must be applied using suitable electrostatic equipment. Consult your Sherwin-Williams
Representative regarding unique applications.

CAUTIONS:
Thoroughly review product label for safety and cautions prior to using this product. Please direct any questions or
comments to your local Sherwin-Williams facility.

CAUTION! Causes eye irritation, causes skin irritation, may cause allergic skin reaction, respiratory irritant, dust
may cause eye and respiratory irritation, dust may form an explosive mixture in air. Avoid breathing dust. Avoid
contact with eyes and prolonged or repeated contact with skin. Use protective clothing and NIOSH approved
respirator. Do not use near sparks or open flame or any type of ignition source. Wash thoroughly after handling. Use
only with adequate ventilation.

FIRST AID:
If on SKIN: Wash thoroughly with soap and water.
If in EYES: Flush with water immediately and procure medical attention. The area adjacent to the coating operation
should be properly ventilated. Cure ovens must be exhausted to the outside atmosphere. All dusts are respiratory
irritants, inhalation of the dust should be avoided. To avoid static electricity buildup, properly ground all equipment.
Provide dust collection equipment with adequate explosion venting; dust clouds of any finely divided organic material
can be ignited by open flame or electrical sparks.

DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN. FOR INDUSTRIAL USE
ONLY. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL INFORMATION.

Note:
Product Data Sheets are periodically updated to reflect new information relating to the product. It is important that the
customer obtain the most recent Product Data Sheet for the product being used. The information, rating and opinions
stated above pertain to the material currently offered and represent the results of tests believed to be reliable.
However, due to variations in customer handling and methods of application which are not known or under our
control, The Sherwin-Williams Company cannot make any warranties or guaranties as to the end results.

HYPEL™ LLDPE 3170 UV 8 NATURAL ** LINEAR LOW DENSITY POLYETHYLENE, 7.0 MFI

TYPICAL PROPERTY VALUES†

PROPERTY	METHOD	UNIT	VALUE
PHYSICAL
Specific Gravity	ASTM D792		0.935
Metal flow (190°C / 2.16 kg)	ASTM D1238	g/10 min	7
MECHANICAL @ 73°F
Tensile Strength at Yield	ASTM D638	psi	2720
Tensile Strength at Yield	ASTM D638	MPa	18.8
Flexural Modulus - 1% Secant	ASTM D790	psi	100,000
Flexural Modulus - 1% Secant	ASTM D790	MPa	655
ARM Impact 1/8" (Notched) @-40°C	ASTM D562B	ft-LB/in	79
Hardness (Shore D)	ASTM D785	-	-
THERMAL
264 psi - ASTM, 1.80 MPa-ISO	ASTM D648	°C	35
264 psi - ASTM, 1.80 MPa-ISO	ASTM D648	°F	95
66 psi - ASTM, 0.45 MPa-ISO	ASTM D648	°C	52
66 psi - ASTM, 0.45 MPa-ISO	ASTM D648	°F	125
OTHER
ESCR (100% IGEPAL)			>1000

**When used unmodified for food contact applications, this copolymer will comply with the U.S. Food and Drug
Administration Food Additive Regulation 21 CFR 177.1520(c)3.1a. This section does not include use in packing or
holding food during cooking. This product is limited to use in contact with food only under the conditions of use C
through H described in table 2 of Sec. 176.170(c), and when contacting fatty foods of Types III, IVA, V, VII-A,
and IX described in table 1 of Sec. 176.170(c), the finished articles are to have a volume of at least 18.9 liters (5
gallons). The uses cited are subject to good manufacturing practices and any limitations, which are part of the
regulations. The regulations should be consulted for complete details.

†The data listed here fall within the normal range of product properties, but they should not be used to establish
specification limits or used alone as a basis for design. This information is not intended as a warranty of any kind.
Buyers must make their own representative test and assume all risks of use, whether used alone or in combination
with other products. Entec Polymers, LLC assumes no obligation or liability of any advice furnished by it or results
obtained with respect to these products. All warranties expressed or implied including warranties of merchantability
for a particular purpose or use are excluded and disclaimed. Entec Polymers, LLC assumes no liability for use of
products in infringement of any patent. The foregoing limitation of remedy and exclusion of liability is reflected in
and is part of the consideration for the price, at which the products are sold by Entec Polymers, LLC. All data
displayed herein has been obtained via testing of injected molded specimens of natural color. Pigmentation may affect
certain properties to various degrees.

Contemporary table, Aluminum Table, Galvanized Steel Tables, In-ground Tables, Polysteel Tables, Recycled Plastic Tables,
Site Furnishing, Park Tables, Outside Tables, Steel Tables, and Tables from your source for material handling equipment.

CONTEMPORARY TABLE DESIGN - 1044

Contemporary table, Aluminum Table, Galvanized Steel Tables, In-ground Tables, Polysteel Tables, Recycled Plastic Tables, Site Furnishing, Park Tables, Outside Tables, Steel Tables, and Tables from your source for material handling equipment.

Contemporary table, Aluminum Table, Galvanized Steel Tables, In-ground Tables, Polysteel Tables, Recycled Plastic Tables,
Site Furnishing, Park Tables, Outside Tables, Steel Tables, and Tables from your source for material handling equipment.