Beam Clamp, Beam Clamps, Lifting Clamp, Lifting Clamps, Plate Clamp, Plate Clamps

ENGINEERED STEEL PRODUCTS

Priced Full Line Products Catalog

PO Box 72659 Providence, RI 02907
Toll free:(800) 421-0314 • In RI:(401) 421-0314 • Fax:(401) 421-5679

VERTICAL PLATE CLAMPS

UNIVERSAL CLAMPS 92 SERIES TYPE CZ92

		Lift and turn over plates in one smooth operation.
		Plates can be turned over or lifted from the horizontal to the true vertical position.
		Available with either standard hookring for use with existing sling hook, or with integral short chain sling for direct fitting on to the crane hook.
		Hardened steel jaws for positive grip and locking mechanism.
		695233, 695234 and 695235 clamps include a jaw and corresponding pad wear indicator to provide visible warning when replacement is required.
		The CZ92 range of clamps can be specially reinforced to withstand frequent dragging. They can also be supplied with a heavy duty ‘sharp leg’where a wedge action is required to separate plates. Price on application.
		LIFT ONE PLATE ONLY AT A TIME
		LIFT ONE PLATE ONLY AT A TIME
		Suitable for all structural steel up to 300 Brinell surface hardness.
		Note: 695232 supplied without lock.


Note: The 1,100 lbs., 3,300 lbs., 4,400 lbs. and 6,600 lbs. W.L.L. units are fitted with moving jaw and fixed pads that incorporate wear indicators.		3) Excessive damage can be quickly caused to the teeth of the moving jaw of a clamp which is continuously used to lift the same thickness of material. Clamps used for this purpose must be inspected weekly to check for wear on the 1 or 2 teeth continuously in contact with the load.
General Safety Note (Vertical Plate Clamps)
1) DO NOT use to lift loads that weigh less than 20% of the W.L.L.


	e.g. 3,300 lbs. clamp should only be used for plates weighing 660-3,300 lbs.
	E.g. 6,600 lbs. Clamp should only be used for plates weighing 1,320-6,600 lbs.
2) Extra care must be taken when lifting plates of less than 20% rated jaw capacity.

PRICING AND DIMENSIONS FOR CZ92 UNIVERSAL PLATE CLAMPS




HINGED UNIVERSAL CLAMPS TYPE CY AND CX			Back to Previous

	The new CY clamp is based on our successful 92 series range of clamps and incorporates the new universal hinged hookring.
	The CX and CY Hinged Universal Plate Clamps have been developed especially for the handling of plate at any angle.
	The CX clamp is particularly suitable for handling fabrications because of the facility of the lifting eye and link.
	LIFT ONE PLATE ONLY AT A TIME.
	Suitable for all structural steel up to 300 Brinell surface hardness.
	For stainless steel and other materials please contact us.

	*Safety First*
	Ensure operators have access to detailed operating instruction supplied with each new clamp.

CX		CY

PRICING AND DIMENSIONS FOR HINGED UNIVERSAL CLAMPS TYPE CY AND CX




HIGH GRIP UNIVERSAL CLAMP TYPE HG		Back to Previous

	These clamps develop a much higher grip on the lifted plate and are complementary to the Universal type. They are particularly suitable for lifting plates with hardened surfaces or stainless steel.
	Available with either standard hookring for use with existing sling hook, or with integral short chain sling for direct fitting on to the crane hook.
	LIFT ONE PLATE ONLY AT A TIME.
	Suitable for all structural steel up to 376 Brinell surface hardness.

PRICING AND DIMENSIONS FOR HG HIGH GRIP CLAMP




GENTLE GRIP CLAMP TYPE TSS (STEEL JAWS)			Back to Previous

	This clamp is specifically designed to lift without marking the surface. Particularly useful for lifting stainless steel when it is important not to impregnate the stainless steel with ferrous material.

		*Safety First*
		Ensure locking mechanism is in the closed position prior to lifting.

PRICING AND DIMENSIONS FOR TSS GENTLE GRIP CLAMP

VERTICAL PLATE CLAMPS