 |
ENGINEERED
STEEL PRODUCTS |
| Priced
Full Line Products Catalog |
PO
Box 72659 Providence, RI 02907
Toll free:(800) 421-0314 • In RI:(401) 421-0314 • Fax:(401) 421-5679 |
|
|
|
|
Back
to Product Category
|
MODEL
25/26-CRRC
|
|
CHAIN DRIVEN
LIVE ROLLER CONVEYOR
(Roll-to-Roll Type)
|
The
Model 25/26-CRRC is a heavy-duty, chain driven roller curve
conveyor commonly used in
conjunction |
|
|
|
 |
|
with
the 25/26-CRR conveyor
to carry heavy unit loadssuch
as pallets and drums. Can be
used in industries like bottling
and steel manufacturing.
Product orientation could be
affected with straight roller
curves. |
|
|
|
16 Widths
Reversible
Chain Driven Rollers
Can Be Slave-driven from
25-CRR
Adjustable HS-Type
Floor Supports Available |
|
|
|
|
|
 |
|
|
|
|
STANDARD
SPECIFICATIONS
|
BED
- Roller bed with 2-1/2 in. dia. x 11 ga. unplated
rollers mounted in 4 in. x 4 ga. powder painted formed
steel channel frame. |
|
BUTT
COUPLINGS – Standard for connecting to
25-CRR, 2-1/2 in. dia. or 2-5/8 in. dia. gravity roller
conveyor. |
|
|
|
DRIVE
– Mounted underneath, placed near center of
conveyor. |
|
MOTOR
– 1 HP–208/230/460/575V–3 Ph. 60 Hz.
Totally Enclosed C-Face. |
|
|
|
| DRIVE
CHAIN – No. 50 circular roller chain. |
|
CAPACITY–4000
lbs. total distributed live load at
30 FPM. |
|
|
CHAIN
GUARD – Formed steel, upper and lower
chain guard mounted to top and bottom of channel frame
to totally enclose drive chains. |
|
|
|
|
FLOOR
SUPPORTS – Now supplied as optional
equipment. |
|
|
|
|
|
|
|
SPEED
REDUCTION – Sealed worm gear C-Face
speed reducer. |
| BEARINGS
– Sealed, pre-lubricated ball bearings. |
|
|
|
| CONVEYING
SPEED–Constant 30 FPM. |
|
|
|
|
|
|
|
OPTIONAL
EQUIPMENT
|
FLOOR
SUPPORTS–HSN Type floor supports are
available with a wide range of adjustment. Specify top of
belt or roller elevation. One support required at every bed
joint and ends of conveyor. Holes in feet for lagging to floor.
Knee braces recommended above HSN-6 support. |
|
FRAMES–4
in. x 5.4 lb. structural channel. |
|
|
|
GUARD
RAILS–Fixed angle (2 in. high x 1/4 in.
steel) guard bolts to top of flange of channel opposite
chain guard. |
|
|
|
ROLLERS
SET LOW–Use angle guard rail. |
|
|
CONVEYING
SPEED–Other constant and variable
speeds. V-belt supplied on speeds under 12 FPM (1 HP).
NOTE: Capacity affected with speed change. |
|
|
|
|
TREAD
ROLLERS–2-5/8 in. dia. x 7 ga. steel
11/16 in. hex spring-loaded shaft (26-CRRC). |
|
|
|
|
|
|
|
MOTORS–Energy
efficient, single phase, brake motor,
other characteristics. 1 HP maximum. |
TOP
SIDE MOUNTED DRIVE–Motor reducer unit
mounted to side of conveyor with drive chain through top
of chain guard. Specify clearances. Minimum elevation top
of rollers 6 in. |
|
|
|
|
TANGENTS–Lengths
available on 5 in. increments
(5 in. roller centers) up to 45 in. OAL. Other roller
centers and lengths available (jackshaft required),
contact us. |
|
|
V-BELT
DRIVE–V-belt supplied between motor and
reducer. |
|
|
|
|
|
|
|
|
ELECTRICAL
CONTROLS–Non-reversing or
reversible magnetic starters and push-button stations.
AC variable frequency drive. |
O-RING
DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit regular
lubrication). |
|
|
|
|
|
|
| PRICES
FOR COMPLETE CONVEYOR INCLUDE: |
|
•
2-1/2” Dia. x 11 Ga. or 2-5/8” x 7 Ga. Roller Mounted
in a 4” x 4 Ga. Formed Channel Frame
• No. 50 Circular Roller Chain
• “C” Face Speed Reducer–Sealed Worm Gear
• 1 HP–“C” Face Totally Enclosed Motor (Specify
Exact Voltage)
• Totally Enclosed Chain Guard
• 30 FPM Conveying Speed
• Less Electrical Controls
• Less Supports |
|
|
|
|
|
25-CRRC (STRAIGHT ROLLERS) NOTE: Chain
Guard on Outside Radius |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
49-3/4" |
51-3/4" |
53-3/4" |
55-3/4" |
|
Between Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
53" |
55" |
57" |
59" |
|
Overall Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4 |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
56-1/4" |
58-1/4" |
60-1/4" |
62-1/4" |
|
90º |
$3,679 |
$3,721 |
$3,762 |
$3,804 |
$3,845 |
$4,579 |
$4,629 |
$4,727 |
$4,777 |
$4,876 |
$4,975 |
$5,073 |
$5,124 |
$5,173 |
$5,222 |
$5,271 |
|
60º |
$3,305 |
$3,334 |
$3,361 |
$3,390 |
$3,418 |
$4,020 |
$4,051 |
$4,112 |
$4,143 |
$4,205 |
$4,267 |
$4,329 |
$4,359 |
$4,390 |
$4,421 |
$4,452 |
|
45º |
$2,842 |
$2,860 |
$2,877 |
$2,894 |
$2,911 |
$3,349 |
$3,370 |
$3,411 |
$3,430 |
$3,471 |
$3,511 |
$3,551 |
$3,571 |
$3,592 |
$3,611 |
$3,631 |
|
30º |
$2,621 |
$2,649 |
$2,677 |
$2,706 |
$2,734 |
$3,097 |
$3,130 |
$3,198 |
$3,232 |
$3,300 |
$3,369 |
$3,437 |
$3,471 |
$3,504 |
$3,539 |
$3,572 |
|
26-CRRC (STRAIGHT ROLLERS) NOTE: Chain
Guard on Outside Radius |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
49-3/4" |
51-3/4" |
53-3/4" |
55-3/4" |
|
Between Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
53" |
55" |
57" |
59" |
|
Overall Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4" |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
56-1/4" |
58-1/4" |
60-1/4" |
62-1/4" |
|
90º |
$4,095 |
$4,166 |
$4,235 |
$4,306 |
$4,377 |
$5,264 |
$5,321 |
$5,435 |
$5,493 |
$5,607 |
$5,722 |
$5,836 |
$5,893 |
$5,950 |
$6,007 |
$6,065 |
|
60º |
$3,726 |
$3,774 |
$3,822 |
$3,871 |
$3,919 |
$4,602 |
$4,656 |
$4,764 |
$4,818 |
$4,927 |
$5,035 |
$5,143 |
$5,197 |
$5,252 |
$5,306 |
$5,360 |
|
45º |
$3,004 |
$3,031 |
$3,057 |
$3,083 |
$3,111 |
$3,613 |
$3,635 |
$3,678 |
$3,698 |
$3,741 |
$3,785 |
$3,828 |
$3,849 |
$3,871 |
$3,893 |
$3,914 |
|
30º |
$2,621 |
$2,649 |
$2,677 |
$2,706 |
$2,734 |
$3,097 |
$3,130 |
$3,198 |
$3,232 |
$3,300 |
$3,369 |
$3,437 |
$3,471 |
$3,504 |
$3,539 |
$3,572 |
|
|
|
|
|
| IMPORTANT
NOTES |
|
|
•
OTHER WIDTHS
For “IN-BETWEEN WIDTHS”,
contact us.
|
•
NON-STANDARD WIDTHS WITH STANDARD INSIDE RADIUS
Require an additional (2) weeks. |
|
•
PRODUCT ORIENTATION
Product Orientation Could be Affected with Straight
Roller Curves. |
|
| |
|
|
|
|
| PRICES
FOR OPTIONAL EQUIPMENT |
|
MOTORS
|
Extra
Motor Price for OTHER THAN: 1 HP-208/230/460/575 V-3 Ph.-60
Hz.-Totally Enclosed. Speed affects
horsepower requirements. |
H.P.
REQ. |
TOTALLY ENCLOSED
|
ENERGY EFFICIENT
|
|
200/208/230/460/
575 V 3 Ph.-60 Hz.
|
115/230 V
1 Ph.-60 Hz.
|
230/460 V
3Ph.-60 Hz.
|
575 V 3Ph.- 60 Hz.
|
|
1 |
N/C
|
$47.71
|
$264.34
|
$264.34
|
|
2 |
$251.87
|
$652.03
|
$534.90
|
$534.90
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OPTIONAL
DRIVES |
|
|
|
|
|
OPTIONAL
FRAME |
|
Drive Type |
Overall Frame Width |
|
22-1/4" to
34-1/4"
|
36-1/4" to
54-1/4"
|
56-1/4" to
70-1/4"
|
Top Side
Mounted C-Face |
$295.26 |
$355.56 |
$415.86 |
Top Side
Mounted V-Belt |
$435.88 |
$496.18 |
$556.48 |
|
|
|
|
|
|
4”
x 5.4 lbs. Structural Channel ........................ |
|
|
|
|
.....................for
30º,
45º,
60º, & 90º........ |
$71.69 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DRIVE
COMPONENT DEDUCTS |
|
|
|
|
|
Less
Complete Motor Drive and Drive Shell (For |
|
|
|
|
Slave
Driving) ........... Deduct.................... |
$643.30 |
|
|
|
|
|
|
|
Less
Drive, to be Slave Driven with Jackshaft
Slave Connection with #40 Chain ...................... |
| #60
O-Ring Drive Chain ......... Add ......... |
$162.31 |
|
|
|
|
|
|
|
|
|
|
|
|
.................................
Deduct ........................ |
$458.10 |
| #50
O-Ring Drive Chain ......... Add ......... |
$231.84 |
|
|
|
|
|
|
|
|
|
|
Less
Drive, to be Slave Driven with Jackshaft
Slave Connection with #50 Chain ...................... |
| Under
5’ -0” OAL use Top Side Mounted or V-Belt Drive. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FLOOR
SUPPORTS |
|
|
|
|
................................
Deduct ......................... |
$458.10 |
Not
Included in Base Price. Use Chart Below for
Required Elevation. |
|
|
|
|
Less
Drive, to be Slave Driven with Jackshaft
Slave Connection with #60 Chain ...................... |
|
|
|
|
|
|
|
|
|
................................
Deduct ......................... |
$458.10 |
|
"HSN"
SUPPORT
|
|
|
|
|
|
|
|
|
|
|
Less
Motor Only (1 HP-208/230/460/575 V-3 |
|
Model No. |
Adjustment to Top of Roller |
Price Each |
|
HSN-1** |
10-1/2" to 12" |
$53.23 |
|
HSN-2** |
12" to 15" |
$53.59 |
|
HSN-3** |
15" to 18" |
$55.38 |
|
HSN-4* |
18" to 21" |
$57.06 |
|
HSN-5* |
21" to 24" |
$59.10 |
|
HSN-6* |
24" to 30" |
$72.53 |
|
HSN-7* |
30" to 36" |
$79.72 |
|
HSN-8* |
36" to 48" |
$92.19 |
|
HSN-9* |
48" to 60" |
$103.22 |
|
HSN-10* |
60" to 72" |
$112.81 |
|
HSN-11* |
72" to 84" |
$119.76 |
|
HSN-12* |
84" to 96" |
$133.91 |
|
|
|
|
|
|
|
|
|
|
|
Ph.-60
Hz.) ............... Deduct ...................... |
$161.40 |
|
|
|
|
Less
Reducer* .......... Deduct ...................... |
|
$175.30 |
|
|
|
|
|
*Less
V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GALVANIZING |
|
|
|
|
|
|
Add
to Base Price ........................................ 40%
All Parts to be Galvanized Construction, except
pulleys (Hot Rolled Steel Painted), Drive Shafts,
Tail Shafts, and Idler Shafts will be Cold Rolled
Steel Construction.
Note: Not Rated for Wash Down Application
Note: Contact Factory for Wash Down Duty
Note: Contact Factory for Stainless Steel Options |
| Singel
Center Leg ......................................................
|
$39.92 |
|
|
|
|
|
|
| *
Knee Braces (Included in support price) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Extra
Braces ..................Add per pair ................... |
$40.17 |
|
|
|
|
OPTIONAL
ROLLERS |
**Less
than 18-1/2” top of roller elevation–
Top Side Mounted Drive Required. |
|
|
|
|
|
|
|
|
|
|
Use
the following Add-on prices for optional
roller sizes and bearings. |
|
|
|
|
|
|
|
|
|
|
| CONSTANT
AND VARIABLE SPEEDS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Regreasable
Bearings with Grease Fittings (25-CRRC
& 26-CRRC) |
Constant
C-Face–Within 16-100 FPM ....No Charge
Constant V-Belt–Within 4-15 FPM .....................
............................... Use V-Belt Drive Add-on |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Conveying Surfaces |
15-3/4" to 23-3/4" |
27-3/4" to 55-3/4" |
|
Between Rail Width |
19" to 27" |
31" to 59" |
|
Overall Frame Width |
22-1/4" to 34-1/4" |
34-1/4" to 62-1/4" |
|
90º |
$411.55 |
$486.35 |
|
60º |
$299.34 |
$336.74 |
|
45º |
$187.01 |
$261.82 |
|
30º |
$149.61 |
$187.01 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ELECTRICAL
CONTROLS |
|
|
|
|
|
| See
below. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| GUARD
RAILS |
|
|
|
|
Angle
Type “A”
2” x 1-5/8” x 1/4” |
|
|
|
|
|
|
|
|
|
| Side
Opposite Chain Guard ... each ......... |
$78.04 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25-CRRC ONLY - 2-1/2" Dia. x 7 Ga. Rollers with 013.1059
Heavy Duty Bearings |
Conveying
Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
49-3/4" |
51-3/4" |
53-3/4" |
55-3/4" |
Between
Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
53" |
55" |
57" |
59" |
Overall
Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4 |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
56-1/4" |
58-1/4" |
60-1/4" |
62-1/4" |
|
90º |
$1,008 |
$1,019 |
$1,030 |
$1,042 |
$1,056 |
$1,274 |
$1,288 |
$1,326 |
$1,332 |
$1,375 |
$1,403 |
$1,431 |
$1,451 |
$1,459 |
$1,481 |
$1,495 |
|
60º |
$733 |
$741 |
$749 |
$759 |
$768 |
$882 |
$892 |
$911 |
$924 |
$952 |
$971 |
$991 |
$1,004 |
$1,010 |
$1,025 |
$1,035 |
|
45º |
$458 |
$463 |
$468 |
$474 |
$480 |
$686 |
$694 |
$709 |
$717 |
$740 |
$755 |
$770 |
$781 |
$786 |
$798 |
$805 |
|
30º |
$367 |
$370 |
$375 |
$379 |
$384 |
$490 |
$495 |
$506 |
$512 |
$529 |
$539 |
$550 |
$556 |
$561 |
$570 |
$575 |
|
26-CRRC ONLY - 2-5/8" Dia. x .219 Wall Rollers with
013.1059 Heavy Duty Bearings |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
49-3/4" |
51-3/4" |
53-3/4" |
55-3/4" |
|
Between Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
53" |
55" |
57" |
59" |
|
Overall Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4" |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
56-1/4" |
58-1/4" |
60-1/4" |
62-1/4" |
|
90º |
$1,226 |
$1,263 |
$1,299 |
$1,335 |
$1,371 |
$1,706 |
$1,748 |
$1,821 |
$1,875 |
$1,961 |
$2,046 |
$2,132 |
$2,175 |
$2,217 |
$2,259 |
$2,303 |
|
60º |
$892 |
$919 |
$945 |
$971 |
$997 |
$1,181 |
$1,210 |
$1,261 |
$1,298 |
$1,358 |
$1,416 |
$1,476 |
$1,505 |
$1,535 |
$1,564 |
$1,594 |
|
45º |
$557 |
$574 |
$591 |
$607 |
$623 |
$919 |
$941 |
$980 |
$1,010 |
$1,056 |
$1,102 |
$1,148 |
$1,171 |
$1,194 |
$1,216 |
$1,240 |
|
30º |
$353 |
$459 |
$472 |
$485 |
$498 |
$656 |
$672 |
$700 |
$721 |
$754 |
$787 |
$820 |
$836 |
$853 |
$869 |
$886 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TANGENTS |
Tangent
Lengths for 25/26-CRRC curves. Tangents are on 5” roller
centers with #50 chain. Odd length tangents,
priced as next whole foot. Price includes jackshaft. Optional
roller centers are available and require jackshaft slave
connection kit, contact factory for pricing. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25-CRRC Tangents with 5" Roller Centers |
|
Conveying Surfaces |
15-3/4" to 21-3/4" |
23-3/4" to 33-3/4" |
35-3/4" to 47-3/4" |
49-3/4" to 55-3/4" |
|
Between Rail Width |
19" to 25" |
27" to 37" |
39" to 51" |
53" to 59" |
|
Overall Frame Width |
22-1/4" to 28-1/4" |
30-1/4" to 40-1/4" |
42-1/4" to 54-1/4" |
56-1/4" to 62-1/4" |
|
10" |
$198.04 |
$221.06 |
$247.79 |
$266.97 |
|
15", 20" |
$396.08 |
$442.12 |
$495.58 |
$533.95 |
|
25", 30", 35" |
$594.13 |
$663.18 |
$743.38 |
$800.92 |
|
40", 45" |
$792.17 |
$884.23 |
$991.17 |
$1,067.89 |
|
26-CRRC Tangents with 5" Roller Centers |
|
Conveying Surfaces |
15-3/4" to 21-3/4" |
23-3/4" to 33-3/4" |
35-3/4" to 47-3/4" |
49-3/4" to 55-3/4" |
|
Between Rail Width |
19" to 25" |
27" to 37" |
39" to 51" |
53" to 59" |
|
Overall Frame Width |
22-1/4" to 28-1/4" |
30-1/4" to 40-1/4" |
42-1/4" to 54-1/4" |
56-1/4" to 62-1/4" |
|
10" |
$209.19 |
$236.04 |
$267.45 |
$289.87 |
|
15", 20" |
$418.26 |
$472.09 |
$534.90 |
$579.74 |
|
25", 30", 35" |
$626.97 |
$708.13 |
$802.36 |
$869.61 |
|
40", 45" |
$836.64 |
$944.17 |
$1,069.81 |
$1,159.36 |
|
|
|
| ELECTRICAL
CONTROLS AND DRIVE SECTION |
|
|
|
MANUAL
START SWITCH or
SAFETY DISCONNECT
|
|
 |
|
|
|
LIMIT
SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER |
 |
|
|
|
|
| #032.1014......................................... |
$117.96 |
|
|
|
|
#033.2032
& #033.2072..................$109.93
Nema 4 |
"START-STOP",
Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase) |
|
|
|
|
|
|
|
|
LIMIT
SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER |
|
 |
|
|
|
|
|
|
|
|
|
#033.2033&
#033.2072...................$160.67
Nema 4 |
|
|
REVERSING
DRUM SWITCH |
|
|
|
|
|
#032.103.......................................... |
$277.28 |
|
|
|
 |
|
|
|
|
|
|
|
|
|
"Fwd-Stop-Rev",
Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase |
|
|
|
|
|
|
|
LIMIT
SWITCH, TIME DELAY-ON,
WITH NYLON ROLLER LEVEL |
|
|
 |
|
|
|
|
REMOTE
CONTROL ROD |
|
|
|
|
|
|
|
|
|
#033.2052
& #033.2072.................$414.31
Nema 4 |
|
Price
per foot of bed length "L"...........$5.27
Use with standard Reversing Drum Switch,
ONLY. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROXIMITY
SWITCH, INDUCTIVE,
(METAL SENSING) |
|
|
 |
 |
FOOT
SWITCH WITH GUARD |
|
|
#032.209.........................................$113.77
115 Volt AC or 24 Volt DC, two wire with
ground, 30mm dia., 10mm range
|
#032.200.............................................$149.85
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
PHOTO
EYE, ON-OFF TYPE |
 |
POWER
CORD AND PLUG (20') |
|
#033.2122......................................$352.68
115 Volt, relay output, light or dark energized, and includes
Reflector. |
| Price................................................. |
$59.10 |
|
(Motor
HP and voltage, etc., must be specified
to size power cord and plug. Max. 1-1/2 HP 1
Phase, 2 HP 3 Phase.) |
|
|
DUAL
TIME DELAY MODULE |
|
|
|
|
|
|
#033.2172.......................................$127.55
For #033.2122 Photo Eye (.5 to 10 seconds
On), (.5 to 10 seconds Off) |
|
|
|
|
|
|
|
|
|
"EMERG.
STOP" PULL CORD SWITCH |
|
|
|
|
|
|
|
|
|
|
|
|
MOUNTING
BRACKETS FOR PHOTO
EYE #033.2122 |
|
|
#032.285
with 032.2851 Turnbuckle
...........................................................$383.38
Nema 4 |
|
|
|
|
|
|
|
|
|
|
|
|
B-05165...........................................$65.34 |
|
|
|
|
|
|
"RED"
EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE |
|
|
|
|
 |
AIR
PRESSURE SWITCH |
|
|
#032.281...one
side.................$4.07 per / ft.
both
sides..............$8.51 per / ft. |
|
#094.191........................................$364.08
Nema 4 |
|
|
EMERGENCY
PUSH BUTTON |
|
|
|
|
|
|
|
|
|
#032.284.............................................$115.93
Nema 4 |
|
|
|
|
NOTE:
PRICING LISTED NOT MOUNTED
OR WIRED |
|
|
|
|
|
|
|
|
|
|
|
PHOTO
EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE |
|
|
|
|
|
|
|
|
|
#032.212
(100mm range, 3.94")......$162.68
#032.2125 (200mm range, 7.87")....$162.68
#033.218 (400mm range, 15.74")....$162.68 |
|
|
|
|
|
|
|
|
|
"PHOTO
EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC |
|
|
|
|
|
|
|
|
|
#033.212B
with 032.21122 Cable.....$248.39
#032.21122 (Cable Only)..................$ 39.92 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC
VARIABLE SPEED DRIVE ADD-ON PRICES
|
|
REPLACEMENT
CONTROLLER
|
|
AC VARIABLE SPEED DRIVES (ALL MOTORS
ARE ENERGY EFFICIENT 3 PHASE)
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
115 VOLT |
ADD ON PRICE
208/230 VOLT |
|
1/2 |
EA-VSC-12-10 |
EA-VSC-12-12 |
|
Price |
$1,015.93 |
$858.49 |
|
1 |
EA-VSC-12-11 |
EA-VSC-12-13 |
|
Price |
$1,187.65 |
$1,051.65 |
|
2 |
N/A |
EA-VSC-12-14 |
|
Price |
~ |
$1,592.49 |
|
THREE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
208/230 VOLT |
ADD ON PRICE
460 VOLT |
|
1/2 |
EA-VSC-01-15 |
EA-VSC-01-18 |
|
Price |
$975.84 |
$1,119.00 |
|
1 |
EA-VSC-01-16 |
EA-VSC-01-19 |
|
Price |
$1,111.72 |
$1,250.63 |
|
2 |
EA-VSC-01-17 |
EA-VSC-01-20 |
|
Price |
$1,592.49 |
$1,705.48 |
|
|
|
|
AC VARIABLE SPEED CONTROLLER ONLY
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
Motor Size |
115 Volt |
208/230 Volt |
|
1/2 |
VSC-10 |
VSC-12 |
|
Price |
$827.54 |
$659.78 |
|
1 |
VSC-11 |
VSC-13 |
|
Price |
$956.53 |
$771.70 |
|
2 |
N/A |
VSC-14 |
|
Price |
~ |
$995.43 |
|
THREE PHASE CONTROLLER INPUT
|
|
Motor Size |
208/230 Volt |
460 Volt |
|
1/2 |
VSC-15 |
VSC-18 |
|
Price |
$876.75 |
$918.82 |
|
1 |
VSC-16 |
VSC-19 |
|
Price |
$876.75 |
$995.43 |
|
2 |
VSC-17 |
VSC-20 |
|
Price |
$1,097.69 |
$1,148.63 |
|
|
|
|
|
|
REPLACEMENT
INVERTER DUTY
ENERGY EFFICIENT MOTORS
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-On . . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
HP |
Part No. |
Price |
|
1/2 |
032.351 |
$450.11 |
|
1 |
032.353 |
$488.05 |
|
2 |
032.355 |
$579.13 |
|
| Brake
Relay Kit (EA-068A).............................. |
$299.70 |
|
|
|
IMPORTANT
NOTES...
|
|
|
•
NOTE #1: Add on price includes standard motor deduct.
• NOTE #2: 2 HP Add On Price includes 5AC reducer
upgrade.
• NOTE #3: All above motors are 230 / 460 Volt,
3 Phase.
• NOTE #4: All above V/S Drive Kits include NEMA
1 / IP30 Junction Box, Controller and Motor.
• NOTE #5: Good for cycle rates of up to 15 cycles
per
minute,
at 1/2 second ramp time, with a
maximum speed of 250 FPM.
• NOTE #6: Drawing No. DG-001146.
• NOTE #7: When AC Variabl Speed Controller is used
with
a Brake Motor, A Brake Relay Kit
(EA-068A) is required. Add an additional
$299.70 for this option.) |
|
|
|
|
|
|
|
NOTES
|
|
|
•
NOTE #1: All above motors are 230/460 Volt,
3 Phase.
• NOTE #2: All above V/S Controllers are mounted
in NEMA 1 / IP30 Junction Box. |
|
|
|
|
ELECTRONIC
CLUTCH BRAKE DRIVE PACKAGE
|
|
Part No. |
Description |
Price |
|
EA-VSC-01-CB |
2 HP Electronic Clutch-Brake Kit |
$2,887.55 |
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-on . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
|
|
NOTES
|
|
KIT
INCLUDES
|
|
|
•
NOTE #1: Good for cycle rates of up to 60 cycles
per minute.
• NOTE #2: 1/10 second Accel and Decel time, with
350 FPM Maximum Speed.
• NOTE #3: 460 Volt Only, Other Voltages, Contact
us.
• NOTE #4: Motor Cooling Blower is 115 Volt,
1 Phase, 60 Hz.
• NOTE #5: Drawing No. EA-VSC-CB.
• NOTE #6: Price Includes 5AC Reducer and #60
Chain
and Sprockets |
|
Part No. |
Description |
|
VSC-01-20 |
AC Variable Speed Controller, 460 Volt, 3 Phase |
|
032.345 |
2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
Part No. |
Description |
|
VSC-01-17 |
AC Variable Speed Controller, 230 Volt, 3 Phase |
|
032.345 |
2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
|
|
 |
|
THIS
STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
|
|
|
|
An
International Electrotechnical Commission (IEC) term that
means: “under short circuit
conditions, the starter shall cause no danger to persons or
installation and shall be
suitable for further use.” The only allowable damage
to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters
meeting this level of com-
ponent protection provides users with less down time and lower
replacement costs.
|
|
|
|
|
|
|
THREE PHASE, IEC COMBINATION MAGNETIC
STARTERS
|
|
H.P.
|
MOTOR
DUTY
|
NON-REVERSING
|
REVERSING
|
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
|
1/2
|
STANDARD EASY
CLEAN ENERG. EFF.
|
EN-20B40
|
EN-23B25
|
EN-46B16
|
EN-57B10
|
$601.32
|
ER-20B40
|
ER-23B25
|
ER-46B16
|
ER-57B10
|
$769.87
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B16
|
EN-46B10
|
|
|
ER-23B16
|
ER-46B10
|
|
|
3/4
|
GEARMOTORS
|
EN-20B40
|
EN-23B40
|
EN-46B16
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B16
|
ER-57B16
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
1
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20B40
|
EN-23B40
|
EN-46B25
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B25
|
ER-57B16
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
1-1/2
|
GEARMOTORS
|
EN-20C10
|
EN-23B63
|
EN-46B40
|
EN-57B25
|
ER-20C10
|
ER-23B63
|
ER-46B40
|
ER-57B25
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
2
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20C10
|
EN-23C10
|
EN-46B40
|
EN-57B40
|
ER-20C10
|
ER-23C10
|
ER-46B40
|
ER-57B40
|
|
|
EN-23C10
|
EN-46B40
|
|
|
ER-23C10
|
ER-46B40
|
|
|
|
EN-23B63
|
EN-46B40
|
|
|
ER-23B63
|
ER-46B40
|
|
|
|
|
|
|
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
|
|
H.P.
|
NON-REVERSING
|
REVERSING
|
NON-REVERSING
|
REVERSING
|
|
|
115 VOLT
|
PRICE
|
115 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
|
1/2
|
EN-1SC10
|
$541.02
|
ER-1SC10
|
$769.87
|
EN-2SB63
|
$652.38
|
ER-2SB63
|
$847.20
|
|
3/4
|
EN-1SC16
|
$559.60
|
ER-1SC16
|
EN-2SB63
|
ER-2SB63
|
|
1
|
EN-1SC16
|
ER-1SC16
|
EN-2SC10
|
ER-2SC10
|
|
1-1/2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Start-Stop” Push-button Station |
|
|
OPTIONAL
STARTER CONTROLS
|
033.1955
|
$76.13 |
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 3 Phase, Non-Reversing |
| Remote
mounted, Nema 1 |
|
|
|
|
|
EA-011
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Fwd-Rev-Stop” Push-button Station |
|
|
|
|
| 033.1965 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Up-Down-Stop” Push-button Station |
|
|
|
|
| 033.1975 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 1 Phase, Non-Reversing |
•
NOTE #1: All starters listed above require 115 Volt
Control Voltage.
• NOTE #2: Above starters are in Nema 3, 4 and 12
Enclosures.
• NOTE #3: The starters included Safety Disconnect,
Overload Relay, and Aux. Contacts as required.
• NOTE #4: IF AN ORDER IS SUPPLIED LESS
MOTOR, AND IS SUPPLYING ANY
ELECTRICAL CONTROLS, THEN MOTOR HP,
VOLTAGE, PHASE, AND FULL LOAD CURRENT
MUST BE STATED ON THE ORDER.
• NOTE #5: PRICING LISTED IS NOT MOUNTED
OR WIRED. |
|
|
|
EA-012
(115 Volt)
EA-017 (230 Volt)
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), Pushbutton Station (033.195),
and (230 V. Only) a Control Circuit
Transformer (As Required).
Note: Above Price does NOT include Photo Eye Mounting
Bracket. |
$1,123.88 |
|
|
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
•
Mounting Brackets for photo eye |
|
|
|
#033.2122
B-05165 |
$65.34 |
|
|
|
|
| •
NOTE #6: Add on |
$107.17 |
for
the above Push Buttons |
|
|
|
|
|
|
|
|
to
be Mounted. |
|
|
|
|
|
|
| •
NOTE #7: Add on |
$214.47 |
for
the above Starters to be |
|
|
|
|
|
Mounted
and Wired. |
|
|
|
|
|
|
| •
NOTE #8: Add on |
$321.28 |
for
the above Starters and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Push
Button Stations to be Mounted and Wired. |
|
|
|
|
| CONVEYOR
WEIGHT CHART |
Conveying
Surface Width |
Between
Rail Width |
Overall Bed
Width |
Outside Radius |
Inside Radius |
No. Of Rollers |
Weights |
|
30º |
45º |
60º |
90º |
30º |
45º |
60º |
90º |
30º |
45º |
60º |
90º |
30º |
45º |
60º |
90º |
|
15-3/4" |
19" |
22-1/4" |
77-3/4" |
65-1/8" |
77-7/8" |
71-1/2" |
58-3/4" |
46-1/8" |
58-7/8" |
52-1/2" |
8 |
10 |
16 |
22 |
364 |
403 |
503 |
607 |
|
17-3/4" |
21" |
24-1/4" |
56-3/4" |
44-1/8" |
56-7/8" |
50-1/2" |
374 |
414 |
517 |
628 |
|
19-3/4" |
23" |
26-1/4" |
54-3/4" |
42-1/8" |
54-7/8" |
48-1/2" |
384 |
425 |
532 |
648 |
|
21-3/4" |
25" |
28-1/4" |
52-3/4" |
40-1/8" |
52-7/8" |
46-1/2" |
393 |
436 |
547 |
669 |
|
23-3/4" |
27" |
30-1/4" |
50-3/4" |
38-1/8" |
50-7/8" |
44-1/2" |
403 |
447 |
562 |
689 |
|
27-3/4" |
31" |
34-1/4" |
110" |
102-1/2" |
98-3/4" |
95" |
79" |
71-1/2" |
67-3/4" |
64" |
10 |
14 |
18 |
26 |
478 |
567 |
657 |
858 |
|
29-3/4" |
33" |
36-1/4" |
77" |
69-1/2" |
65-3/4" |
62" |
489 |
581 |
674 |
881 |
|
33-3/4" |
37" |
40-1/4" |
73" |
65-1/2" |
61-3/4" |
58" |
512 |
609 |
707 |
928 |
|
35-3/4" |
39" |
42-1/4" |
71" |
63-1/2" |
59-3/4" |
56" |
523 |
523 |
724 |
952 |
|
39-3/4" |
43" |
46-1/4" |
67" |
59-1/2" |
55-3/4" |
52" |
546 |
651 |
757 |
999 |
|
43-3/4" |
47" |
50-1/4" |
63" |
55-1/2" |
51-3/4" |
48" |
568 |
679 |
790 |
1046 |
|
47-3/4" |
51" |
54-1/4" |
59" |
51-1/2" |
47-3/4" |
44" |
590 |
707 |
824 |
1092 |
|
49-3/4" |
53" |
56-1/4" |
120" |
112-1/2" |
108-3/4" |
105" |
67" |
59-1/2" |
55-3/4" |
52" |
612 |
735 |
852 |
1137 |
|
51-3/4" |
55" |
58-1/4" |
65" |
57-1/2" |
53-3/4" |
50" |
634 |
763 |
880 |
1182 |
|
53-3/4" |
57" |
60-1/4" |
63" |
55-1/2" |
51-3/4" |
48" |
656 |
791 |
908 |
1227 |
|
55-3/4" |
59" |
62-1/4" |
61" |
53-1/2" |
49-3/4" |
46" |
678 |
819 |
936 |
1272 |
|
All
weights are conveyor weights only. Accessories, crating, etc.,
are not included.
Note: Add 25% for 26 Rollers. |
|
Chain Driven
Live Roller Curve Conveyor, Roll-to-Roll, Chain Driven Live
Roller Conveyors, Conveyor, Live Roller
Conveyors, Powered Live Roller, Conveyors, and Roller Conveyors
from your source for material handling equipment.
|
Back
to Product Category |
 |
|