 |
ENGINEERED
STEEL PRODUCTS |
| Priced
Full Line Products Catalog |
PO
Box 72659 Providence, RI 02907
Toll free:(800) 421-0314 • In RI:(401) 421-0314 • Fax:(401)
421-5679 |
|
|
|
|
Back
to Product Category
 |
|
|
|
|
7-Year
Product Warranty
|
| |
 |
5.
Loading on ResinDek panels is not to exceed design
loads during or after installation.
Design load
recommendations are as follows:
A.
Do not exceed 1,500 lbs. per pallet jack (live
and dead load) on ResinDek EF.
B.
Do not exceed 2,000 lbs. per pallet jack (live
and dead load) on ResinDek LD.
C.
Do not exceed 3,000 lbs. per pallet jack (live
and dead load) on ResinDek MD.
D.
Do not exceed 4,500 lbs. per pallet jack (live
and
dead load) on ResinDek HD.
E.
Do not exceed recommended loads per
pallet
jack (live and dead load) on ResinDek
Xspan.
6. Allowable loads based on testing conducted by
us with
36" o.c. spans on ResinDek
EF, LD, MD, and HD.
Longer spans may reduce load carrying
capacities.
Please contact us for allowable point
loads, uniform
loads, and pallet jack (live and
dead load) loads for
ResinDek Xspan.
7. We must be notified in the event of a problem with
any
of its materials, and given a minimum
of two weeks
notice to correct the problem on its
own, and/or
personally visit the site if necessary,
prior to repairs and
remedies by others.
8. There will be no warranty coverage for acts of God,
exposure to weather, or for impact
or concentrated
loads.
9. This warranty will be considered void in the event
of
prolonged exposure to standing
water on the ResinDek
panels.
10. There will be no warranty coverage for acts of
negligence by the installer,
the customer, or the end user.
11. This warranty is between us and the customer.
Warranty will flow through
to the end user for the
entire period of this warranty.
|
ResinDek®
7-Year Product Warranty
We hereby warrants all of ResinDek® panels to be free
from defect, structurally sound, and able to safely carry
the specified design loads as specified. At our option,
we
will either replace or make a reasonable allowance for
repair to all ResinDek Panels found to be defective for
a period of seven (7) years from date of shipment to the
jobsite.
Qualifications to this warranty are as follows:
1. All panels must be installed
in accordance with ResinDek
Installation Instructions.
2. All panels must be properly
unloaded, protected and
stored prior to their installation.
Care shall be taken to
protect the panels from excessive moisture
before,
during, and after installation.
3. ResinDek EF, LD, MD,
and HD panels must be
installed with only approved fasteners
over the gauge
and type of corrugated metal decking
for the load on
the floor as approved by us.
4. ResinDek Xspan™ must
be supported at intervals
approved by us with structural supports
capable
of withstanding loads imposed. Fastener
number,
pattern and type must be approved by
us. |
|
|
| Care
& Maintenance |
|
While
a ResinDek® floor provides long-lasting durability,
safety and cleanability, it must be properly installed
and
maintained to avoid costly floor problems, repairs and
hazards that may potentially void all product warranties.
Whether your ResinDek® floor finish is Clear Diamond
Seal®, Gray Diamond Seal® or ESD, the surface
can be
easily cleaned using a damp mop or standard cleaning
solvents without fear of damaging the surface.
Cleaning solutions that have worked particularly well
include
water, diluted isopropyl alcohol, and many off the shelf
detergents and floor cleaners. Never use methylene
chloride or paint thinners, which will damage
ResinDek finishes. Also avoid prolonged soaking,
hosing down, or wetting of all ResinDek products.
ResinDek UF (unfinished) will clean up similar to
other unfinished wood products.
For touching up surface blemishes and scratches
on your
ResinDek Gray Diamond Seal or ESD finish, a can of
color-matched spray paint can be obtained from us.
When using the touch-up paint, be sure to shake the
spray
can for at least 60 seconds for proper color mixing.
For
best results, spray using repeated, light coats of paint
and
allow adequate drying time before resuming floor traffic.
Read all touch-up paint manufacturer labels and
warnings before using resin-based products and work
|
in
a fully ventilated area with proper protection for
eyes and hands.
For repairing deeper cracks or holes in ResinDek panel
surfaces, it is possible to use standard fiberglass or
polymer
resin patch compound commonly used in auto body repair.
To repair a damaged ResinDek panel surface, mix an
appropriate amount of hardener and resin and apply the
mixture into the damaged area, as directed. Use a putty
knife to spread and skim the surface smooth before the
material hardens. Depending on the depth and size of the
damaged area, more than one application may be required
to build up the patch material at or above the ResinDek
surface level. Allow adequate drying time as directed.
After drying, use 80 grit sandpaper to sand the resin
patch
flush with the ResinDek panel surface. Feather sand the
area,
taking care not to damage the surrounding ResinDek panel
finish.
After sanding the repaired area, apply touch-up paint
as
instructed earlier in this video module. If painting reveals
that
the patched surface is not flat, it may be necessary to
sand
and repaint the area again.
If you have additional questions about repairing ResinDek
panels, contact us by e-mail or phone (listed above). |
|
|
|
ResinDek,
Mezzanine Flooring Panels, Mezzanine Floors, Floor Panels,
ESD Flooring, ResinDek Drill Screws,
XLD50, LD50, MD, HD, UF, and Xspan from your source for
material handling equipment. |
|
|
Back
to Product Category |
 |
|